Jump to content
SAU Community

Recommended Posts

i put a rb25det version1 in a r32 sky...i kept the rb20det loom exept for the injector clip,i trim to fit the rb25 injector plug in my rb20 wiring to fit the rb25 injector...so now the trouble is when i crank i have spark on plug and signal on injectors but wont open for fueling in engine. the fuel pressure is good only if i put visegrip on the return line(yes the fuel line are connect right way)55lbs fuel pressure

i try both computer rb20 and 25,other cas but no fuel again

please help

so if you keep the vise grips on the return hose will it start?

doesnt the RB20 have a dropping resistor for the injectors in the harness?

no the only thing the vise grip do is maintin the fuel pressure to 50-55psi and for the resistor i dont know thats why im asking

thanks

the fuel pressure is good only if i put visegrip on the return line(yes the fuel line are connect right way)55lbs fuel pressure
Then the regulator is stuffed. Try swapping the regulator from your 20.

spray some carby cleaner or start ya bastard into the throttle body while cranking and see if it fires.

take off the fuel pressure line and put into a bottle and check that there is plenty of flow from the fuel pump. might be too weak.

check power to the injectors and negative pulse at the injectors with a LED test light,

if thats good then more than likely the injectors are seized

ok so i have good pression from the fuel pump and she working in my 240 sr20det without prob.

i have pusle at the injector but dosent click loud

if this possible that the 6 injectors are seized????

if a shoot carbcleaner in the intake the motor want but dosent start

and what the matter with pin 112 and 114 : i need to cross them or not...anyway both way dosent start

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...