Jump to content
SAU Community

Recommended Posts

  • Replies 103
  • Created
  • Last Reply

Top Posters In This Topic

Just thought this would make for some interesting convo :wassup:

ill start: I went to Tecoma primary- And Upwey high school :headspin:

Oooh close, I'm

Primary - Fairhills Primary - Ferntree Gully

Secondary - Fairhills High School - Ferntree Gully (AKA Fairy Land)

Bahahahahaha

Nothing is woggier than a sweaty Marchole!

I remember punching the living shit out of some guy from marcellin during one of the big fights at shoppingtown.... Then some prick hit me :) lol memories!

You were a shoppo hanger? bwahahaah! Did you get the .30c meal deal at maccas (0.30c cone and a free water) so you could 'hang' legally? :)

no ****ing shit?! :headspin: :headspin:

i went to both those schools!! Tecoma for primary, and Upwey High School, and for about 20 years i lived in Belgrave! My mum still lives up there. I only left Melbourne about a month ago for up here, but went up their regularly. Thats freaky.. You would have only been a couple of years below me too. I bet you know people that i know :) hey do you Nathan Haley? I'm friends with his brother. Tanya Houston? Kristie Davies? Any of those names sound familiar?

oh, and i went to Monash Clayton for one year (sucked), and then Swinburne Hawthorn for 4 years or something.

okay, I'm adding to this list coz I wanna get to know a few of you guys before I get my 'line later this year.

Primary: New Gisborne

Secondary: Braemar College

Tertiary: Melbourne Uni

New Gis and Braemar are all kinda country schools, so dun worry about not knowing them :wassup:

red hill primary -> padua college -> peniunsula grammar -> geelong grammar
Osborne Primary - Mornington

Mornington H.S.

Good to see there are some people from the mornington peninsula on the forums!

I went to:

Mt. Martha Primary

Woodleigh School

Monash Uni and still there for another 2 and a bit years...

Wantirna Heights Primary

Ferntreegully North Primary

Bayswater West Primary

Fairhills Primary

Knox Technical School

Swinburne Croydon

and spent a year short coursing at Alabama Uni ,Birmingham,(AL,USA)Roll Tide.

You were a shoppo hanger? bwahahaah! Did you get the .30c meal deal at maccas (0.30c cone and a free water) so you could 'hang' legally? ;)

lol i caught the bus home a couple of times via shoppingtown!

I was never a shoppo hanger, i was only at whitefriars till year 8 so my shoppo hanging wasnt cultivated yet...

Do you remember the guys from both Marcellin and Whitefriars who used to get changed into their 'kappa' snap pants after school to hang at shoppingtown????

Bahhahahaha classic.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...