Jump to content
SAU Community

Recommended Posts

McDud,

it seems you have once again consumed the Bong Water!

Be sure that you were mistaken with the TV Show on Discovery Channel was in fact "Future Weapons"

I won't back up the other hacks,

But be sure Scotty (I run solo Stephens) and Brad and I will be handing out some *Chop Chop to Team Green Wang Fail

Eat a Dick

  • Replies 85
  • Created
  • Last Reply

Top Posters In This Topic

It's ok big boy...

May as well vent your frustration now..

Better then out on track, as the only chopping that you'll be doing will be the grass you collect when spinning out...

Looking forward to Team Green Wang Pump taking the trophey this time :P

You clowns will end up in the pits with a worn clutch or chain issue.

Shit, you could share a Coke and a Kit Kat with Bart in the Pits, you might even get lucky and hit the showers early together

Fag!

You clowns will end up in the pits with a worn clutch or chain issue.

Shit, you could share a Coke and a Kit Kat with Bart in the Pits, you might even get lucky and hit the showers early together

Fag!

a mid race shower sounds like a great idea... i would estimate that buy around 19-20min in to the race the jolly green wang pump team will have built a solid enough lead to pit for a shower break... if the lead isn't solid enough we will just use the pump on it!

i can't foresee us wearing a clutch 3 times in a row... the only thing being worn will be our pimp hands on your cheak, when we slap you for not earning your keep... "now back to yo corna biatch... bring me sum paper"

  • 2 weeks later...
Looks like I am in need of a new co-driver.

Paul has been whipped into shape by Lauren and pussied out for a flower smelling festival or something such pansy like.

P.S. when do we pay for this shindig?

PM heading out tonight for payment

PC is faggetery personified!!!!! :thumbsup:

Team Green Wang Pump...i just got off the phone from Kart track. They are fitting your kart with pneumatic jacks to make it easier to get it off the ground....they are also running 4 extra pit crew for your Kart.....also restocked plenty of Clutches for you. :)

Gents,

Incorrect BSB and Acc N# sent out.

Please drop the last digit from the BSB (1) and add it to the beginning of the Acc number.

Well picked up Tom

Cheers

MG

Sorry lads, I'm going to have to pull out, I'm crook as a dog and not really keen on putting around like a sweaty pig acting as a moving chicane... Tifosi racing therefore announce their immediate and regretful withdrawal..

Mike, may you be spared a couple of young, determined woglings nipping at your heels haha... Till next time then? :blink:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...