Jump to content
SAU Community

Recommended Posts

Hey guys,

been reading through motorsport section and this section and I just cannot seem to find exactly what i'm after re: E85 and fuel setups.

I was planning on running 2 x external pumps, but after reading, it may be simpler to run 1.

My setup is - RB26/30, gt3076r 0.82 ext gate on E85 - hoping for between 330 - 360rwkw

I have:

walbro intank pump as pickup/feed pump, 3 L surge tank, 1 x external 044, nismo fpr, 1000cc injectors - I was wondering if this will be sufficient? Or if I will need 2 x externals (due to E85).

***ALSO***

How does the external pumps get wired up? Do they get wired in with the standard intank pump (so internal and external prime at the same time/powered same time) - was thinking of doing this with an extra relay to keep voltage up.

Thanks

-Matt

BTW - POST PICS :P

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/
Share on other sites

  • Replies 109
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

400rwkw is about the safe limmit for a single 044- depending how much torque your puting down...

I would go with an aftermarket pump, rated for e85 and with a higher flow rate... like an aeromotive A1000? Or a Weldon inline 1100 http://www.weldonracing.com/products/Produ...line+Pumps.html .

I don't like twin pumps...

J.

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5287020
Share on other sites

400rwkw is about the safe limmit for a single 044- depending how much torque your puting down...

I would go with an aftermarket pump, rated for e85 and with a higher flow rate... like an aeromotive A1000? Or a Weldon inline 1100 http://www.weldonracing.com/products/Produ...line+Pumps.html .

I don't like twin pumps...

J.

Unfortunately Weldon pumps are only rated for gasoline/petrol. They would not be a good choice for E85.

Compatible with Gasoline Only (not compatible with alcohol / ethanol based fuels)
Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5287924
Share on other sites

thanks guys, i'd like to know why people don't rate having 2 externals???

I've seen a lot of ppl speaking of 'x' amount of power out of single 044 external but many are relating to pump fuel. How much more does E85 flow the PULP?

cheers

Well on mine it used 45% more on power runs, who cares about normal running (it's less of course)

I use 2 o44's external and have zero issues. STACKS of big power cars use them, usually in the boot with a 2L or so surge tank.

Edit; Mine maxed out 1000's on the fourth dyno run, there's vids on YouTube but the lesson is that 1000's on my setup (26/30 like you) was no good. They lasted until a touch over 400rwkw before there was no more duty cycle to go. Went with Injector Dynamics 2000's and very happy. It drives so much better now aswel which I wasn't expecting. Speak to Trent at Mercury Motorsport for pricing, I got them from him. I think your setup will be a heap of fun to drive, good luck with it all

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5287948
Share on other sites

Hey guys,

been reading through motorsport section and this section and I just cannot seem to find exactly what i'm after re: E85 and fuel setups.

I was planning on running 2 x external pumps, but after reading, it may be simpler to run 1.

My setup is - RB26/30, gt3076r 0.82 ext gate on E85 - hoping for between 330 - 360rwkw

I have:

walbro intank pump as pickup/feed pump, 3 L surge tank, 1 x external 044, nismo fpr, 1000cc injectors - I was wondering if this will be sufficient? Or if I will need 2 x externals (due to E85).

***ALSO***

How does the external pumps get wired up? Do they get wired in with the standard intank pump (so internal and external prime at the same time/powered same time) - was thinking of doing this with an extra relay to keep voltage up.

Thanks

-Matt

BTW - POST PICS :/

YOU WILL NEED TWO 044S, 113 HP AT THE CRANK PER LITRE OF E85, PETROL IS 165HP PER LITRE, AN 044 IS ONLY CAPABLE OF 3.6LTPM AT 55 PSI. THE WALBRO AS LONG AS IT IS THE BIGGER RATED UNIT WILL BE FINE. 1000CC INJECTORS WILL BE OK.

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288060
Share on other sites

AN 044 IS ONLY CAPABLE OF 3.6LTPM AT 55 PSI. THE WALBRO AS LONG AS IT IS THE BIGGER RATED UNIT WILL BE FINE. 1000CC INJECTORS WILL BE OK.

Umm what?

There is no way any Walbro will flow more than a Bosch 044. I've been down that road before.

Bosch 044 will have a minimum flow 5Litres/min (300LPH) at thier 5bar rating & 12 volts. No idea where you get 3.6LPM from.

That's the issue with Bosch pumps and their ratings as you'll see below, the 044 is NOT rated @ the same pressure as the 040.

Bosch 040 Fuel Pump Specs:

Bosch Part Number: 0 580 254 040

Minimum Current: 12 Volts

Operating Pressure: 94 PSI (6.5 Bar)

Minimum Flow @ Outlet: 80 GPH (300 LPH)

Fuel Pump Location: In Tank

High Temperature Reduction: 8 GPH (30 LPH)

Weight: 930 Grams (2.05 Pounds)

Bosch 044 Fuel Pump Specs:

Bosch Part Number: 0 580 254 044

Minimum Current: 12 Volts

Operating Pressure: 72.5 PSI (5 Bar)

Minimum Flow @ Outlet: 80 GPH (300 LPH)

Fuel Pump Location: In-Line

High Temperature Reduction: 8 GPH (30 LPH)

Weight: 1030 Grams (2.27 Pounds)

http://boschfuelpumps.com/

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288100
Share on other sites

realistically - is it possible that with boost around 25psi I may see 370+ rwkw (been reading NYTSKY's build thread).

what other single pump would flow enough and be suitable for E85?

I dont want to be running out of fuel all because I opted for the wrong external pump OR didn't go down the 2 x external pump options.

Seems there are a few conflicting options... which makes it hard lol.

Appreciate the input, keep it coming.

-Matt

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288182
Share on other sites

Umm what?

There is no way any Walbro will flow more than a Bosch 044. I've been down that road before.

Bosch 044 will have a minimum flow 5Litres/min (300LPH) at thier 5bar rating & 12 volts. No idea where you get 3.6LPM from.

That's the issue with Bosch pumps and their ratings as you'll see below, the 044 is NOT rated @ the same pressure as the 040.

Bosch 040 Fuel Pump Specs:

Bosch Part Number: 0 580 254 040

Minimum Current: 12 Volts

Operating Pressure: 94 PSI (6.5 Bar)

Minimum Flow @ Outlet: 80 GPH (300 LPH)

Fuel Pump Location: In Tank

High Temperature Reduction: 8 GPH (30 LPH)

Weight: 930 Grams (2.05 Pounds)

Bosch 044 Fuel Pump Specs:

Bosch Part Number: 0 580 254 044

Minimum Current: 12 Volts

Operating Pressure: 72.5 PSI (5 Bar)

Minimum Flow @ Outlet: 80 GPH (300 LPH)

Fuel Pump Location: In-Line

High Temperature Reduction: 8 GPH (30 LPH)

Weight: 1030 Grams (2.27 Pounds)

http://boschfuelpumps.com/

The guy said 3.6L/min @ 55psi.. 55psi is ~75% of of 72.5psi.. 3.6L is ~75% of 5L..

His maths isn't exact but it's pretty close..

Edited by bubba
Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288189
Share on other sites

Umm what?

There is no way any Walbro will flow more than a Bosch 044. I've been down that road before.

Bosch 044 will have a minimum flow 5Litres/min (300LPH) at thier 5bar rating & 12 volts. No idea where you get 3.6LPM from.

That's the issue with Bosch pumps and their ratings as you'll see below, the 044 is NOT rated @ the same pressure as the 040.

Bosch 040 Fuel Pump Specs:

Bosch Part Number: 0 580 254 040

Minimum Current: 12 Volts

Operating Pressure: 94 PSI (6.5 Bar)

Minimum Flow @ Outlet: 80 GPH (300 LPH)

Fuel Pump Location: In Tank

High Temperature Reduction: 8 GPH (30 LPH)

Weight: 930 Grams (2.05 Pounds)

Bosch 044 Fuel Pump Specs:

Bosch Part Number: 0 580 254 044

Minimum Current: 12 Volts

Operating Pressure: 72.5 PSI (5 Bar)

Minimum Flow @ Outlet: 80 GPH (300 LPH)

Fuel Pump Location: In-Line

High Temperature Reduction: 8 GPH (30 LPH)

Weight: 1030 Grams (2.27 Pounds)

http://boschfuelpumps.com/

Those specs are crap - got to this site http://www.bosch.com.au/content/language1/...s/fuelpumps.pdf

Then you will see that they are only good for 200LPH @ 5Bar = 3.33L/min @ 12Volts.

I've never seen a single 044 ever make 400rwkw safely on our dyno.

And as for 6x 1000cc/min not being enough for 400rwkw on E85 thats crap too - I bet your fuel pressure is dropping or your trying to make power above 10 000rpm.

I've made 420rwkw on an xr6t with 6x 660cc/min injectors with a base fuel pressure of 4bar with 16psi of boost and that was with 1x 044 and 1x walbro intank in semi parallel pump setup.

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288279
Share on other sites

Well on mine it used 45% more on power runs, who cares about normal running (it's less of course)

I use 2 o44's external and have zero issues. STACKS of big power cars use them, usually in the boot with a 2L or so surge tank.

Edit; Mine maxed out 1000's on the fourth dyno run, there's vids on YouTube but the lesson is that 1000's on my setup (26/30 like you) was no good. They lasted until a touch over 400rwkw before there was no more duty cycle to go. Went with Injector Dynamics 2000's and very happy. It drives so much better now aswel which I wasn't expecting. Speak to Trent at Mercury Motorsport for pricing, I got them from him. I think your setup will be a heap of fun to drive, good luck with it all

The injector dynamic injectors ID1000s are awesome but by my calcs they should be good for at least 500rwkw on E85 unless its a very ineffcient engine.

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288285
Share on other sites

Those specs are crap - got to this site http://www.bosch.com.au/content/language1/...s/fuelpumps.pdf

Then you will see that they are only good for 200LPH @ 5Bar = 3.33L/min @ 12Volts.

I've never seen a single 044 ever make 400rwkw safely on our dyno.

And as for 6x 1000cc/min not being enough for 400rwkw on E85 thats crap too - I bet your fuel pressure is dropping or your trying to make power above 10 000rpm.

I've made 420rwkw on an xr6t with 6x 660cc/min injectors with a base fuel pressure of 4bar with 16psi of boost and that was with 1x 044 and 1x walbro intank in semi parallel pump setup.

:O

Well there you go then :banana:

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288298
Share on other sites

Umm what?

There is no way any Walbro will flow more than a Bosch 044. I've been down that road before.

Bosch 044 will have a minimum flow 5Litres/min (300LPH) at thier 5bar rating & 12 volts. No idea where you get 3.6LPM from.

That's the issue with Bosch pumps and their ratings as you'll see below, the 044 is NOT rated @ the same pressure as the 040.

Bosch 040 Fuel Pump Specs:

Bosch Part Number: 0 580 254 040

Minimum Current: 12 Volts

Operating Pressure: 94 PSI (6.5 Bar)

Minimum Flow @ Outlet: 80 GPH (300 LPH)

Fuel Pump Location: In Tank

High Temperature Reduction: 8 GPH (30 LPH)

Weight: 930 Grams (2.05 Pounds)

Bosch 044 Fuel Pump Specs:

Bosch Part Number: 0 580 254 044

Minimum Current: 12 Volts

Operating Pressure: 72.5 PSI (5 Bar)

Minimum Flow @ Outlet: 80 GPH (300 LPH)

Fuel Pump Location: In-Line

High Temperature Reduction: 8 GPH (30 LPH)

Weight: 1030 Grams (2.27 Pounds)

http://boschfuelpumps.com/

the specs are great flow them in the car at 55psi with a -6 supply line or smaller and there goes the specs, the walbro in the tank is pumping at 0 pressure as a lift pump, no one said anything about a walbro out flowing an 044 at 55 psi.

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288335
Share on other sites

You may as well spend the extra 200- 220 bux on the pump that will give you a piece of mind plus you can always go e85 after if you feel like it.

can of worms much??

opinions on seeing how i go with 1 x external 044 (seems like it can be done)... is it worth seeing how it goes and how safefly or just go with 2 x externals?

cheers

Edited by s2d4
Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288653
Share on other sites

What about the actual quality of the pump?

044 seems to be the industry standard for feed pumps?

As for internal, the 044 can be mounted internally too, either as a lift pump or even inside the surge tank as feeds to the rail.

the specs are great flow them in the car at 55psi with a -6 supply line or smaller and there goes the specs, the walbro in the tank is pumping at 0 pressure as a lift pump, no one said anything about a walbro out flowing an 044 at 55 psi.
Edited by s2d4
Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288657
Share on other sites

One 044 pump will be fine as long as you don't try and run stupid high rail pressure and run a seperate relay to power the pump.

I don't actually see how two pumps gives you "safety". If one pump fails and the other isnt enough your still screwed. I see the complications of running two pumps more likely to cause issues.

FYI - Running 425 rwkw on e85 with one 044 in tank and run the 141 mph to back it up as well :P

Yer - Thats No surge tanks, no lift pumps, even stock fuel lines and fuel filter.

...

Link to comment
https://www.sau.com.au/forums/topic/324383-e85-fuel-setup/#findComment-5288727
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...