Jump to content
SAU Community

Recommended Posts

Hey,

Before this DIY just to reiterate my car does not have an airbag, if your car does you may have to hunt around to find the correct procedure to remove your steering wheel as you don't want the airbag going off in your face. The usual warning applies too, do this at your own risk, I'm only showing how I did it, I'm not responsible for any damage to your car

Difficulty: Low

Time: ~30 - 60 minutes

Tools you will need

- Screwdriver set

- Socket set (preferably a very sturdy big one, with extension bar and a 19mm socket)

- Mallet (Rubber type)

Note: Make sure your wheels are dead straight when you do this so it's easy to put your steering wheel back on straight!

1) Unhook the negative terminal off your battery or alternatively remove the horn 10 amp fuse from the fuse box in your engine bay, do this to save your neighbors all the honking lol

P1040724.jpg

2) Locate your steering wheel :P

3) Get a very (VERY) thin flat head screw driver and very gently slide it under your horn button and lift up. You may have to do this from several angles so it comes out nice and smooth. For God's sake take your time and don't damage anything, not the strongest piece of equipment in your car, but having that said it's pretty easy.

P1040723.jpg

4) Disconnect the power cord going to the steering wheel button

P1040725.jpg

5) Remove all bronze Phillips head screws from inside (the deeper one is grounding the horn button, just remember this will have to go in back the way in came or your horn won't work

P1040728.jpg

6) Remove the plastic rim that was holding the horn in place (again, be gentle)

7) Remove the metal....thing.... from the center of the wheel (it'll just slide out)

P1040731.jpg

8) You are now looking at a big silver nut, grab your 19mm socket and loosen it off but don't take it off, keep it just hanging on by a few threads

P1040727.jpg

9) Grab your mallet and gently but firmly tap the back of the steering wheel whilst supporting it with your knees so it doesn't rattle everywhere, you may have to alternate sides every now and then, just take your time

P1040732.jpg

10) Once the wheel can be "rocked" free, look behind the steering wheel and you'll see a white electrical plug, disconnect this plug

11) Take off the silver nut (remember it was hanging on by a few threads so the wheel doesn't fly off when your pulling on it)

P1040734.jpg

12) Take off the backing plastic shroud and you'll be able to remove the electrical cord

P1040735.jpg

Done! :D

P1040733.jpg

Prior to installing the wheel again, put a little bit of grease on the "teeth" of the steering column as this'll make it slide back on nice n' smooth (plus it'll make it easier to remove the steering wheel in the future)

Installation is the reverse of the above steps,

Any comments or improvements are welcome,

Cheers,

Sean

  • 2 years later...

This instructions are not correct, I am trying to follow these in my 94 Gtr and first of all the metal thing doesnt come out before the 19 inch nutits slotted underneith the nut so how can you pull it out with the nut still on there?? and i am up to the part where you hammer the steering heel off slightly and how bloody hard to you have to hit this?? I am trying my hardet to pull the thing and its not budging

Got it woohoo.... I found If you hit the steering wheel with your palms left and right like your playing the drums.. It wedges it out of place,. Anyways thanks for this I managed to get it even tho one bit was abit confusing :D

  • 6 months later...

R32 GTR Nissan Workshop Manual makes it very clear that:

1. To remove the Horn Button, insert a flathead screwdriver through the slot at the side of the steering column to release the Horn Button from behind.

2. To remove the Steering Wheel, it is not to be struck - no unbalanced axial forces.

The correct tool is a Steering Wheel Puller.

Refer WorkShop Manual Page CH-315.

R32 GTR Nissan Workshop Manual makes it very clear that:

1. To remove the Horn Button, insert a flathead screwdriver through the slot at the side of the steering column to release the Horn Button from behind.

2. To remove the Steering Wheel, it is not to be struck - no unbalanced axial forces.

The correct tool is a Steering Wheel Puller.

Refer WorkShop Manual Page CH-315.

Thanks for the info mate, you're 100% correct on that one.

I didn't have access to the workshop manual at the time of the original write up

For those playing at home, Link - Page 592

what I did with my steering wheel was left the bolt on with a couple of thread and just pulled the steering wheel towards myself as hard as I could, until it flew at me (but the bolt stops it from attacking you) at least with this method you don't have to whack the steering wheel ;)

  • 1 month later...

I managed to replace the steering wheel with a Momo corse And I have used A HKB Boss Kit Hicas Compatible....

Now I really dont get it... How sensitve is the Steering angle sensor? WHen I am cruising down the highway and give it a hit which activates the HICAS... It must detect that my steering wheel is not straight and the HICAS light now comes on.. Stays on until I turn the car off. When I turn it back on it only comes back when I am driving straight for awhile and give it a hit.

I am confused as to what needs to line up there are no proper instructions All I see on the boss hub is an arrow pointing UP and it says TOP next to it. I tried to line it up while the car was In park position .. the wheels did look straight but I found out when I started to drive that it wasnt It was pointing at 1 o Clock.... My question is is this what is making the HICAS come on ? How sensitive is it? I am practically doing this blind as I cannot find any documentation saying how to install a HICAS steering wheel back on a r32 gTR

Can someone help please ??

Edited by GTRAAH
  • 1 year later...

Hey all,

I know this is an old thread but I recently had to do this again and I was unable to find the "hole" in the steering column to pop out the horn from the rear. As it turns out the R32 GTR steering wheels come in two varities depening on the age. The older style wheel has plastic on the back which follows the wheel spokes (such as the one I have). The other newer variety has a round plastic cover on the back. This newer style wheel is the one mentioned in the service manual. I was unable to see any way to access the horn from the rear via the steering column so I ended up using the same method for extracting the horn button.

There is another thread with somebody showing the two styles of wheels on this forum.

I hope this update is of use to somebody out there.

Cheers,

Sean

Few issues with some things in this DIY

1. The R32 GTR steering wheel does have GTR embossed on the horn button (or it's been replaced with a GTS/t's)

2. Should be no need to remove the plastic at the back of the steering wheel

3. Should not need to remove the "metal thing" when removing the steering wheel either

4. The horn connector unclips and you can even feed the wires through the square hole

5. Never wobble the steering wheel from side to side to release the wheel (if you cant pull it straight back then use the puller)

6. Horn button is removed using a small flathead from the front

The other thread does have a Picture of the 89-92 and 93-94. But I believe both are removed and fitted the same.

  • Like 1

Hey all,

Here is the thread I mentioned earlier where they are discussing the 'newer' and 'older' style of steering wheels: http://www.skylinesaustralia.com/forums/topic/349288-fitting-an-original-r32-gtr-steering-wheel/

"Older" style below - See plastic spokes that follow wheel at the back

Older style BNR32 wheel

"Newer" style below - See round plastic behind wheel

Newer style BNR32 wheel

Here is a screen shot of the workshop manual - appears to be the 'newer' style of wheel with the round plastic with a hole at the base allowing you to remove the horn. The 'older' style of wheel does not have this hole. If anybody with a 1994 GTR could take a few pictures of their steering wheel we can compare.

Workshop Manual

Cheers,
Sean

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I started this repair and got as far as "fixing" the holes with some fibreglass. God all those years working on boats came back quickly. I decided I'd reach out to some rust guys just to see what they would say about it. I came across a guy about 40 mins away and went to see him. He said the windscreen needs to come out, that there might be some more bits around the windscreen and he'd quote them at the time. But his quote was $300 to remove and replace windscreen and $3k for the damage he can see. He said he could respray the roof for $1200 and the bonnet for another $800 (somebody has previously rattle canned it, its horrendous). This is $5300 + any small additional bits. It's a lot, I get that and the name of one of my fave youtube channels 'Not Economically Viable' comes to mind.  I'm not being financially rational, but I've taken him up on the quote. He's opening a new shop in November with more room, so we're waiting for that. I'll leave the currently missing headliner out until then. I'm looking forward to it being fixed and having the paint looking nice again (lots of clear coat issues on the roof too). / flame suit on.
    • Oh and some up-and-comings; New rear drivers wheel bearing. I'll do that this weekend while the diff is out. The car is already up and the d/c axles and missing exhaust will help with space. This is the last bearing for me to do and I've been dragging my feet on it. I also have some new EBC blue stuff pads for the car and some new brake fluid. I haven't ever flushed the fluid in this car and looking forward to it. I have 600 degree fluid to put in. Not exactly "race fluid" but better than the typical stuff I have been using.
    • A proper clutch/plate type mechanical diff with quite a lot of pre-load and high locking % is better for drifting. Much more consistent in its behaviour. A helical can be annoyingly vague and inconsistent in how it responds under the sorts of abuse found in drifting.
    • Some updates here. I pulled the entire interior out, minus some trim to respray the seats with Colourlock dye. It turned out really nice though I accidentally let the dog in the car after and she scratched up the front seat.  This is what it looked like before, the colour was just washing out everywhere but thankfully the leather was in good nic. Then after the respray   And after the bloody dog jumped in The headliner is out waiting to be retrimmed, but it will stay out now until Nov - see why below. I replaced the stereo/headunit with a period-styled Android headunit. I have no after pics, but I'll get some. This is because of the missing pixels. I tried to fix this twice with replacement ribbon cables but couldn't. Also the bluetooth interface I'd bought for this was crap. Then there's the rusty roof. Pics and info in this other thread. I have decided to get this repaired professionally, but I'll update that thread. This is why the headliner will stay out for now. I'll be getting the roof and bonnet resprayed at the same time the rust is fixed. I also had an interesting issue with my drivers door lock.  For a small period I was having issues getting any 12v power to the car - I mean *any*. It would have no dash lights, nothing. It happened while I was at the shops and I couldn't get in the car. So, we had 2 problems. The most pressing here is that I was locked out. I have only a single physical key hole on the car, the drivers door and no amount of turning would unlock the car. Surely it doesn't need power for this? The second issue is why am I losing all power periodically, The battery isn't dead, its almost like the battery isn't even there. Two issues that were surprisingly easy to fix. You fellow BMW over-engineering lovers will appreciate this. The lock in the door has 5 states; mechanical lock, electric lock, neutral, electric unlock, mechanical unlock achieved at -90 degrees, -45 degrees, 0 degrees, 45 degrees and 90 degrees. Although, the unlock is towards the front of the car, so opposite for LHD countries. Sticking the key in and turning 45 left or right is what is used 99% of the time. It activates the central locking etc. 90 degrees is for dead battery access and, obvs, only un/locks the one door. But because the mechanical lock is never used and is 27 years old, it seizes up. I was totally unable to turn the key far enough to get to the mechanical unlock (At the time of locking myself out, I didn't even know this was a thing). I eventually did it with some vicegrips and teflon spray.  I made a quick vid for other E39 peeps.   The battery issue is totally new to me also - It wasn't making sufficient contact between the post and the terminal. The terminal was bolted on tight, but the car wouldn't have power. After checking the battery with my multimeter I accidentally contacted the terminal and the battery post and the car got power. The battery was only a few years old and in good condition. I cleaned the post and the terminal with a wire brush, bolted it back on tight and never had the issue again. I'm still surprised that despite having solid contact it didn't work. Also, the car was getting Warragamba sized pools of water in the back when it rained. My initial concern was another rust problem. But when I went out on Weds while it was raining and while I had no headliner in I could see a steady stream of water coming through the roof mounted aerial. As this aerial is for the (now removed) car phone I pulled it out and whacked a blanking grommet in the hole. It seems fine now. I'm thinking I might get the hole permanently filled when the rust is fixed. Moving forward and things in progress; The tailgate needs some attention. I have taken all the trim off to clean it all and address some small rust spots. I have partially done all of this but I'll finish it up hopefully this weekend. As all the trim are now entirely devoid of trim clips I have bought a heap of strong velcro and I'm hoping it does a good enough job as any of this trim in good condition is super expensive and usually in Europe as we dont have many of the wagons here. Suspension and brakes!!! This is exciting. In the front; New control arms New sway bar links New lower Eibach springs (the only modification I'm planning on this car) M Sport shocks (these came with the car and will replace the longer shocks in the car) New top mounts Used 540i calipers (stock brakes suck!) New 540i disks and pads (22x296 mm for 528 and 30x334 mm for 540i) New front wheel bearings (thank all that is holy for bolt on bearings!) Annnnd in the back; New control arms New sway bar links Adjustable air suspension arms (fool the car into what the current height is so the self levelling suspension can match the new front ride height) New ball joints I'll also be doing a brake fluid flush while I'm in there. I'm planning on switching the car over to the 16's that came with it so I can clean up and respray the M Sport 17's. They've lost a lot of colour over the years and have some gutter rash. None of this will start until the E90 is back.
    • You mean you will regret it for drifting duties? I don't quite follow.
×
×
  • Create New...