Jump to content
SAU Community

Recommended Posts

no it didnt

sorry, was 208, just checked dyno sheet.

50 psi base pressure, + 15psi boost = 65psi .. should give it abit more fuel..?

in saying that, i should be able to work out where im at with the below. theres also an article done by autospeed regarding flow rates vs pressure, basically showing that pressure increases = quite small increases in flow.. so what are stock injectors good roughly? i need to find a maximum safe setting for base pressure. http://autospeed.co.nz/cms/title_Boosting-...86/article.html

stole this from another forum:

The flow is supposed to increase according to the following formula.

F2=F1 x SQRT (P2/P1)

So, assume you have 270cc/min injectors at 36 psi pressure difference, then, if you increase fuel pressure to 42 psi, the resulting flow will be:

F2=270 x SQRT (42/36) = 292cc/min

This formula will work with pressure difference, have in mind that there is always some pressure present at the intake manifold, and it needs to be substracted from the fuel rail pressure in order to obtain the pressure difference.

Like Mcquirk said, doubling fuel pressure will lead to 1.4 times the flow, for 270cc injectors, that is some 380cc/min. BUT, the problem now will be the fuel pump, which likely won't give you the necessary flow at such a high pressure, so, it's much better to install larger injectors and work them near their test pressure.

Edited by tarmac

Dont wind it up too high, the walbros loose heaps of flow when the pressure is wound up, they only flow 500hp worth of fuel at about 40 psi, give it 70 psi, and they flow about 350hp. TBH kkr turbos dont have a great rap in regards to power vs boost needed vs lag

Dont wind it up too high, the walbros loose heaps of flow when the pressure is wound up, they only flow 500hp worth of fuel at about 40 psi, give it 70 psi, and they flow about 350hp. TBH kkr turbos dont have a great rap in regards to power vs boost needed vs lag

yeah i realise theyre shit turbos but i got it cheap. ill get the internal as tight as possible and with electronic boost control can only do me best to avoid lag / boost threshold, otherwise no worries just to drive around it.

KKR430, around i think 230rwkw is about the most anyone has made.

on the hub dyno it'll be higher, probably 240-250 (same as your 208 with factory turbo)

Plenty of results in the RB25 dyno sticky thread.

Sounds like a happy dyno that turbo will not make that power at 14psi

ive done the same turbo on another dynapack that time by st hitec in auckland with a engine thatd done 230k's, did 242rwkw, power fc, larger injectors. this tune was done by glenn suckling who has the 1600hp gtr running 7's.. even if it is abit 'happy' it gives an indication of what they can do. they are cars in the 260kw range with these turbos. an 2 degrees timing was the difference between 233rwkw and 256rwkw. a/f's are hovering around 12 .

moral of story;

kkr430 / dsr430 turbos while not the best with their shitty internal wastegates that you need to load alot of preload on and the fact the interal barely opens, are decent turbos on 25's and you can get away with standard injectors with a fuel reg.

Edited by tarmac

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...