Jump to content
SAU Community

Recommended Posts

hey guys, what oil should i put in my diff? its in an R33gtst, should i use the 80-90 or the thicker 80/90-140? (not sure if its 80-140 or 90-140) also, should i use normal diff oil as apposed to LSD oil? as i beleive the diffs are VLSD and dont necessarily needs LSD oil

any help is apreaciated

cheers

Link to comment
https://www.sau.com.au/forums/topic/328173-80-90-or-8090-140-lsd-or-non-lsd/
Share on other sites

80-140 i would use on a track car, 80-90 for a street/track car. Nissan specifies 80-90 for japanese conditions iirc for rear LSDs

whats iirc? and is that an lsd fluid or normal?

mines a VLSD, would it need special lsd oil or standard gear oil?

Flushed and filled the LSD on both my 33's a couple of days ago with Castrol SAF-XA 80w-140 Full Synthetic Limited Slip Rear Axle Oil. No complaints so far and was told it’s a good oil. I’ve heard that if you have the limited slip diff, you must put LSD oil in or it will not work correctly but you can put LSD oil in non LSDs.

Run everyday 80w90 in your standard R33 GTS-T diff, mineral or synthetic. This will be fine unless it sees alot of track work - in which case you might want an 85w140 or similar. Note that you do not need to use a limited slip oil in a viscous LSD as a viscous LSD uses its own unservicable fluid inside the diff centre to operate. However, using limited slip oil will not do it any harm (aside from most mineral limited slip oils being a monograde 90 - non existent viscosity range).

Only mechanical diffs requires limited slip oil with anti-chatter additives.

Run everyday 80w90 in your standard R33 GTS-T diff, mineral or synthetic. This will be fine unless it sees alot of track work - in which case you might want an 85w140 or similar. Note that you do not need to use a limited slip oil in a viscous LSD as a viscous LSD uses its own unservicable fluid inside the diff centre to operate. However, using limited slip oil will not do it any harm (aside from most mineral limited slip oils being a monograde 90 - non existent viscosity range).

Only mechanical diffs requires limited slip oil with anti-chatter additives.

well i have put an anti chatter aditive in and its still grinding or "chatting" when turning, i cant for the life of me figure out whats wrong with it!

Did you read what I wrote mate? lol :(

You have a viscous diff, it does not need anti chatter additive...hence when you put it in it did nothing :D

Could be a manner of things wrong with it...these are use once and throw away diffs. Buy another one off eBay or put in a proper LSD.

lol do not trust many second hand items on eBay unless it's a solid state business with some impeccable feedback. Great nick is also a subjective use term haha. The plus to it is, if you choose to go with a decent LSD...you can get the centre installed in your spare diff housing while your car is still on the road...that's if you kept the old diff :D

Try Castrol SAF-XA out, if the LSD starts to behave strangly and locks up around a roundabout or in carparks (I heard it happening with Redline Shockproof in the diff, not sure if it was the grade 90w-140 or the fluid itself), just dump the fluid and go a different one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...