Jump to content
SAU Community

Recommended Posts

hey guys, what oil should i put in my diff? its in an R33gtst, should i use the 80-90 or the thicker 80/90-140? (not sure if its 80-140 or 90-140) also, should i use normal diff oil as apposed to LSD oil? as i beleive the diffs are VLSD and dont necessarily needs LSD oil

any help is apreaciated

cheers

Link to comment
https://www.sau.com.au/forums/topic/328173-80-90-or-8090-140-lsd-or-non-lsd/
Share on other sites

80-140 i would use on a track car, 80-90 for a street/track car. Nissan specifies 80-90 for japanese conditions iirc for rear LSDs

whats iirc? and is that an lsd fluid or normal?

mines a VLSD, would it need special lsd oil or standard gear oil?

Flushed and filled the LSD on both my 33's a couple of days ago with Castrol SAF-XA 80w-140 Full Synthetic Limited Slip Rear Axle Oil. No complaints so far and was told it’s a good oil. I’ve heard that if you have the limited slip diff, you must put LSD oil in or it will not work correctly but you can put LSD oil in non LSDs.

Run everyday 80w90 in your standard R33 GTS-T diff, mineral or synthetic. This will be fine unless it sees alot of track work - in which case you might want an 85w140 or similar. Note that you do not need to use a limited slip oil in a viscous LSD as a viscous LSD uses its own unservicable fluid inside the diff centre to operate. However, using limited slip oil will not do it any harm (aside from most mineral limited slip oils being a monograde 90 - non existent viscosity range).

Only mechanical diffs requires limited slip oil with anti-chatter additives.

Run everyday 80w90 in your standard R33 GTS-T diff, mineral or synthetic. This will be fine unless it sees alot of track work - in which case you might want an 85w140 or similar. Note that you do not need to use a limited slip oil in a viscous LSD as a viscous LSD uses its own unservicable fluid inside the diff centre to operate. However, using limited slip oil will not do it any harm (aside from most mineral limited slip oils being a monograde 90 - non existent viscosity range).

Only mechanical diffs requires limited slip oil with anti-chatter additives.

well i have put an anti chatter aditive in and its still grinding or "chatting" when turning, i cant for the life of me figure out whats wrong with it!

Did you read what I wrote mate? lol :(

You have a viscous diff, it does not need anti chatter additive...hence when you put it in it did nothing :D

Could be a manner of things wrong with it...these are use once and throw away diffs. Buy another one off eBay or put in a proper LSD.

lol do not trust many second hand items on eBay unless it's a solid state business with some impeccable feedback. Great nick is also a subjective use term haha. The plus to it is, if you choose to go with a decent LSD...you can get the centre installed in your spare diff housing while your car is still on the road...that's if you kept the old diff :D

Try Castrol SAF-XA out, if the LSD starts to behave strangly and locks up around a roundabout or in carparks (I heard it happening with Redline Shockproof in the diff, not sure if it was the grade 90w-140 or the fluid itself), just dump the fluid and go a different one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
    • Well the articals keep saying a Q50s (Skyline in Japan) with a new Manual gearbox. I like the talk about the new looks with the round tail lights. I hope they bring back the retro look like they did with the Z
×
×
  • Create New...