Jump to content
SAU Community

Recommended Posts

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Just grab the usual injector, pump and ECU upgrade and enjoy the power. I assume you have a manifold and know this wont go near bolting up to the std manifold. If you decide its too laggy for you then I have an 8cm housing that will bring it on qbout 300-400rpm earlier that i would be interested in swapping for your 10cm housing

my favourite RB25 turbo setup. I have done about 6 or 7 now. The latest was low mount external gate. 320rwkw on 18psi completely std internals.

You will love it, should be reliable if done correctly.

This is a customers 4door R33 (std internals apart from 260 drop in cams and no vct) 6boost manifold, blitz gate and T67....

post-34927-1278754601_thumb.jpg

my favourite RB25 turbo setup. I have done about 6 or 7 now. The latest was low mount external gate. 320rwkw on 18psi completely std internals.

You will love it, should be reliable if done correctly.

This is a customers 4door R33 (std internals apart from 260 drop in cams and no vct) 6boost manifold, blitz gate and T67....

320kw!

that is massive... i've got 280kw with 17psi

Ill be making a manifold or adaptor myself. What is the boost limt i can run and what power at which psi have you guys seen with this setup? Also where can i get springs for the trust wastegate?

i have a high mount trust manifold here i've been tryin to sell if you want, make me a reasonable offer and its yours.

Just had the car pictured above on the dyno, only change was we fitted a set of Camtech drop in's (http://www.skylinesaustralia.com/forums/Rb20-Rb26-Rb26-Camshaft-t308743.html) Car still has std head and bottom end.

Blue is before cams.

Red is after cams.

post-34927-1278822136_thumb.jpg

Nope, thats why ill get it going on say 7psi now, then buy pump , injectors etc. Any more advice or info to help me along?

dude

seriously u should listen to what ppl are saying, dont just go strap on a large turbo with no supporting mods

a

just do the basic stuff

ecu or piggyback

injectors

nice dump pipe and exhaust mods

and a turbo manifold

fuel pump

then the other stuff later, u will f**k something up by doing it the way u intend on doing it, + the lag that will happen and then only 7psi comes thru might as well leave it stock till u can afford to do it properly

dude

seriously u should listen to what ppl are saying, dont just go strap on a large turbo with no supporting mods

It seems you have missed the OP's topic all together.

He is asking what else is needed once he has this turbo bolted on, and what he can do with it in the meantime. I dont see an issue, chill.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Just get rid of the orignal low impedance injectors, replace with modern high impedance injectors, and you won't need the resistors. Wire direct, as per any other engine.
    • Tao, we're not talking about the ECU boost ref. We're talking about the wastegate signal source.
    • Flapping up and down is a consequence of the varying pull on the belt. When the engine speed is suddenly increased, the tension in the belt increases too. When that engine accel changes to decel, the tension is reduced and turns up as a little extra length of beltes between the pulling and dragging pulleys. That extra length flaps up, then down. There's all sorts of other harmonic stuff going on too.
    • hello ladies and gentlemen so i’ve swapped a rb26dett into my r33 gtst and ive come across many speed bumps but its nearly over what im having issues with is the injector resistor box that are normally on the RB26 fuse box but im still using my rb25 fuse box and as a result my injectors aren’t getting power and is the last thing i need to figure out so the car can start. can anyone help me out on where i can find a wiring diagram for the rb26 harness to see where the injectors are supposed to receive power 
    • The boost pressure at the compressor cover will be higher than at inlet manifold. lets say, trying to hold 20 psi flat at 7000 RPM. If your wastegate opens at 20 psi measured at the compressor cover, the engine may only be seeing 16 psi. Your base pressure reading at engine would be 20psi by 4K and 16psi by 7K while your MAP at compressor housing still reads 20psi at 7K. For this reason your ECU's MAP source is never on the compressor cover. This difference isn't a major concern if you're using an electronic boost controller (EBC).
×
×
  • Create New...