Jump to content
SAU Community

Recommended Posts

as the title says, i have my hicus still in and hooked up to stock etc, but the hicus light on my dash turns on after 5 mins of driving and dosent turn off unless the car turns off, what would be causing this? and how do i fix it? does the light mean my hicus is buggered?

cheers

What was the last thing you did to the car before the light started coming on?

It means it is getting an error of some sort and going into its failsafe mode. You need to work out what is causing the error.

I once had it happen when I shorted the speed signal wire, kept happening. Simply reset the factory ECU (disconnected the battery over night) and hey presto was fine again.

Have you taken your steering wheel off lately? if it's not quite on straight, after a few minutes of driving HICAS will think you're driving in a really big circle and throw up an error..

Does your speedo still work?

What was the last thing you did to the car before the light started coming on?

It means it is getting an error of some sort and going into its failsafe mode. You need to work out what is causing the error.

I once had it happen when I shorted the speed signal wire, kept happening. Simply reset the factory ECU (disconnected the battery over night) and hey presto was fine again.

its been doing it since i got it, ill try disconnecting the battery, both terminals?

Have you taken your steering wheel off lately? if it's not quite on straight, after a few minutes of driving HICAS will think you're driving in a really big circle and throw up an error..

Does your speedo still work?

i havnt, but ive had the car for about 3 weeks so i dont know what the last ownder did,but how would it know that the steering wheel is off center? its only alen screws...

speedo is fine!

the way it knows is there's a hicas related clock spring type wheel behind the steering wheel that turns with your steering wheel. so it keeps track of the angle. 'steering angle sensor'

but i dont know why ppl keep saying check if your steering wheel is off by a tiny bit. coz the splines dont allow you to be off by a tiny bit. it's very noticeable if you're off if only by one tooth.

i suggest taking your boss kit off and check that it has the appropriate holes in the back for the steering angle sensor to lock into. also, check that the sensor is still there.

Edited by Munkyb0y

There is a steering angle sensor behind the boss, HICAS uses steering angle and speed input to decide what it's doing. Even one tooth out will freak the system out.. I'm talking teeth of the splined shaft that the boss goes on to, not the 6 bolts that hold the steering wheel to the boss.

The sensor is a big white looking disc thing with two posts standing proud of it... really hard to miss.. as soon as you take the boss off there it is.

But +1 for binning HICAS. You don't have as much of a weight saving in the R33's but I hate HICAS and removing it gave me more confidence in the abilities of the car as opposed to not being entirely sure what the back end was going to do..

Fortunately, my Stagea came from the factory without it :)

The sensor is a big white looking disc thing with two posts standing proud of it... really hard to miss.. as soon as you take the boss off there it is.

But +1 for binning HICAS. You don't have as much of a weight saving in the R33's but I hate HICAS and removing it gave me more confidence in the abilities of the car as opposed to not being entirely sure what the back end was going to do..

Fortunately, my Stagea came from the factory without it :)

ok an how is the disc supposed to sit? or am i just making sure its in there?

also, while where on the topic, how hard is it to bin the hicus? is it as simple as unbolting and unpluggin the wires and putting in the bar? or will i need to screw around with the wireing etc, and will i need a wheel alignment? how hard is it? whats involved?

Mine did this. Would always come on just outside of Sydney on the way back to Canberra, but never any other time....inclusive of the way TO Sydney :S

I personally just pissed it off with a lock bar when I got my suspension etc done, but that's obviously not fixing the problem (unless of course you agree that HICAS itself is the problem in the first place)

His is an R33.. I know the 32 will light up the HICAS light if the fluid level is low but doubt the R33 does the same..

yeh i thought it still did as it simply doubled as a hicas/steering fluid warning. im probably wrong, i dont like to meddle in r33 things usually lol

do r33's have a separate warning light for the steering fluid sensor?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...