Jump to content
SAU Community

Recommended Posts

After the success of the last Repco sale thanks to SAU members, I have been asked to organise another car display for Saturday the 31st July at REPCO Modbury.

This time, we are after a few more cars, as the display will extend to the patch of land behind Repco, near the Bunnings entrance.

This time round, I'll be trying harder to get the CTS drift car, and maybe a few 34/35R's on display!

Same deal as last time, Repco will be offering Trade Discount cards for those that dont already have one, for each person to help out. Julie will also be providing $50 towards the BBQ, and supply BBQ, Gas, and Tent if needed.

So who's up for another day of talking Sh!t and watch cars fail/skid on North East Road? :)

Nigel

Link to comment
https://www.sau.com.au/forums/topic/328721-repco-car-displaybbq-round-2/
Share on other sites

  • Replies 99
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

better idea than getting the CTS car on board is asking Simon Michaelmore to bring down the AM performance S14. club sponsor and all. show off his work, and you have a much, much higher chance of getting it

better idea than getting the CTS car on board is asking Simon Michaelmore to bring down the AM performance S14. club sponsor and all. show off his work, and you have a much, much higher chance of getting it

i reckon i could get tristan smith down in his s14 aswell if needed

well i don't have my daughter and i don't have anything on

but i didn't call the last one that successful

maybe i over estimated the food side of things maybe i over estimated who would help and how much... maybe

not 100%, but just not convinced

well i don't have my daughter and i don't have anything on

but i didn't call the last one that successful

maybe i over estimated the food side of things maybe i over estimated who would help and how much... maybe

not 100% out just not convinced

what are you getting at exactly?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...