Jump to content
SAU Community

Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

The one Nathan works on has a massive restore thread on performace forums.

http://www.performanceforums.com/forums/sh....php?t=67227917

93 pages

2770 posts

that's probably gotta take the record for most EPIC build thread ever????

just spent about an hour reading random parts of this thread. i could never match his dedication to his car. absolutely incredible attention to detail! it does kinda show that even if you put massive bucks and countless hours into hotting up your L-series motor you still get problems and not a lot of satisfaction (his words not mine!). and yes i know that will offend some viewers lol. if my c210 coupe was gunna get a power increase at the wheels, it would be coming from an RB conversion and nothing else. just my opinion :-)

93 pages

2770 posts

that's probably gotta take the record for most EPIC build thread ever????

it does kinda show that even if you put massive bucks and countless hours into hotting up your L-series motor you still get problems and not a lot of satisfaction (his words not mine!). and yes i know that will offend some viewers lol. if my c210 coupe was gunna get a power increase at the wheels, it would be coming from an RB conversion and nothing else. just my opinion :-)

If you crunch the right numbers and do the research first, most to all of the problems he had will not be there in the first place.

eg. Just on the cam & lash pad problem he had:

I'm using N42 length valves (ex USA) in my P90 head, but as I'm using a factory reground cam and the core diameter is smaller, the valve length is never going to be an issue. The after market new billets break to easily & therefore a factory re worked cam is by far, much better.

The bottom line in any rebuild is DO THE RESEARCH FIRST then you can do the job right the first time.

I'm looking at over 600Nm @ about 4500rpm on less than 10psi boost from my L Series. I would like to see the $$$$$ figure getting that from your RB, because I did the research for that some time back as well.

Far too many rebuilds have breakage lists and I don't plan on having one of them at all.

Cheers, D

i will get some pics up soon ,mine is a lot crappier than that one but i was in japan last week and bought heaps of good shit ,new fenders ,new exhaust ,coil overs ,big brakes ,deeeep dish work meisters ,bracing ,diff mounts ,ajustable caster rods ,parts for theses cars are easy to get but bug bucks ,its already got a cusco 2 way and a modified L28 with tripple mikuni carbs ect

Ahh, so you bought Jash's car? Awesome project :bunny: The KGC10 build thread on PF is my car, whaddya need to know, Denzo? :(

Oh and btw the issues I had with the L-series were 99% casued by the person who built it in Japan. We ended up starting from scratch, and the cylinder head was redone by Knight Engines in Adelaide, and Nathan did the bottom end and assembly. Ran sweet as a nut after that. Puts out 190rwhp and sounds great, so yeah I'm happy with it.

Edited by Babalouie

yes its jashes old car its a bit of a rust pig but its being repaired properly at the moment ,i will also get the engine freshend up ,ive bought heaps of new parts for the car i cant stop buying ,theres so much cool shit for these things ,just courious what was needed to rego your car ,where did you get seatbelts from ect. :nyaanyaa:

yes its jashes old car its a bit of a rust pig but its being repaired properly at the moment ,i will also get the engine freshend up ,ive bought heaps of new parts for the car i cant stop buying ,theres so much cool shit for these things ,just courious what was needed to rego your car ,where did you get seatbelts from ect. :)

I dunno if it's gonna be the same in WA, but in NSW the engo accepted that Klippan non-inertia reel seatbelts were okay, front and rear.

At the back, you'll find that the c-pillar sheetmetal and floorpan will already have seat belt mountings behind the trim

supplies301.jpg

supplies265.jpg

At the front, it's just the regular Klippan kit, but with the longest available stalk buckle (i think 450mm, cos the mount is so far back on the tunnel).

supplies263.jpg

supplies085.jpg

Umm...apart from seatbelts, I think I didn't have to change or add anything else for rego/engo. Tail lights and indicators (which blink red) were ok for the age of the car.

I think the only hassles I had on rego were things like noise and ride height :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...