Jump to content
SAU Community

Recommended Posts

ok cool, ive seen some exhausts on evo's that sit to close to the bumper and would burn it easily.

yeah i got the Regu 06&R on mine.

yeah this sat in and even my old hks hi-power was angled so it burnt it to

hows the regu sit? and the sound? i saw one on yahoo the other day and i was going to grab it but i missed the end of the auction

Hey guys just recently got my R33 a few weeks ago. It's pretty much stock however it has a full 3 inch apexi exhaust and a pod filter. Will be installing BC racing coilovers in it very soon to give it a nice stance.

Enjoy,

post-86893-0-09132500-1318156956_thumb.jpg

post-86893-0-51244700-1318156996_thumb.jpg

post-86893-0-07728400-1318157047_thumb.jpg

Edited by roonVR

yeah this sat in and even my old hks hi-power was angled so it burnt it to

hows the regu sit? and the sound? i saw one on yahoo the other day and i was going to grab it but i missed the end of the auction

its angled a little but sits out of the way from the bumper which is good i want to show off this titanium tip i dont want it hiding lol. and the sound is pretty quiet from the inside but is loud enough on the outside and when you put your foot down it screams, also love the sound of the wastegate at high rpms it sounds insane. the other day i had my window down overtaking someone and i could hear it louder as the sound was bouncing off there car it was awesome. ill have to show you sometime :)

its angled a little but sits out of the way from the bumper which is good i want to show off this titanium tip i dont want it hiding lol. and the sound is pretty quiet from the inside but is loud enough on the outside and when you put your foot down it screams, also love the sound of the wastegate at high rpms it sounds insane. the other day i had my window down overtaking someone and i could hear it louder as the sound was bouncing off there car it was awesome. ill have to show you sometime :)

haha yeah... ah nice, i would say its louder than my car, especially cause ive got 2 big resonators compared to 1 on the regu system

would probably sound like my old hi-power i would reckon, just less droney cause of the decat lol

haha yeah... ah nice, i would say its louder than my car, especially cause ive got 2 big resonators compared to 1 on the regu system

would probably sound like my old hi-power i would reckon, just less droney cause of the decat lol

yeah i still have a cat even though its a 3inch hi flow. my car isnt droney at all when cruising its very quiet. but id say once i get the dump and front pipe on it should be more louder.

yeah i still have a cat even though its a 3inch hi flow. my car isnt droney at all when cruising its very quiet. but id say once i get the dump and front pipe on it should be more louder.

yeah i dont think my car is too droney, but its quiet for an evo exhaust thats for sure... maybe thats why it doesnt seem droney

was droney on the hks, but that had 1 resonator though

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...