Jump to content
SAU Community

Recommended Posts

Any pointers?

I've jump started it from all sorts of things from GTi-R to a tow truck with twin batteries it still wouldn't start. In fact I've melted 2 jump start cable..

It just crank slowly, crank again then crank again till the cable melts...but funny enough it did start last weekend. Any ideas? It seems like there's not enough power to the starter to crank it into life. Funny enough the power windows refused to work as well.

Link to comment
https://www.sau.com.au/forums/topic/33004-r33-wouldnt-start/
Share on other sites

it might help if u have fuel in the car:D possibilities are starter motor?? did u play with the fuses?? i played with the fuses last time in my car and put one in the wrong place and it wouldnt jump start at all...it would crank over and then die. have u tried putting another battery in your car to see if its the battery at fault?

i dunno....good lucks with it

Link to comment
https://www.sau.com.au/forums/topic/33004-r33-wouldnt-start/#findComment-662476
Share on other sites

There's fuel but doesn't seem like a whole lot in there. Possibly drop another 5L in there and see how it goes...

Which fuse(s) should I check?

With batteries..haven't tried that but the battery shouldn't matter - at least with my other cars even if the battery's screwed, I can still jump start it just that it can't be charged.

Link to comment
https://www.sau.com.au/forums/topic/33004-r33-wouldnt-start/#findComment-662538
Share on other sites

coils not producing spark? spark plugs stuffed? I would say if you have cranked this car till the jumper cables have melted you would have done some serious damage to the starter, as it is only ment to run for 5 secs or so. Also, Im with Chucky, make sure your engine is properly earthed to the chassis, because a bad earth connection can make wires heat up and melt, especially when your using lots of amps when cranking.

Link to comment
https://www.sau.com.au/forums/topic/33004-r33-wouldnt-start/#findComment-664129
Share on other sites

And if your +ve wire or -ve has melted that would explain the slow cranking short of a stuffed starter...

Sumo

P.S. Sometimes its easier to just take it to a autoelec and they should if they are decent give you a heads up on what is going on, free of charge. I know at my work we do.

Link to comment
https://www.sau.com.au/forums/topic/33004-r33-wouldnt-start/#findComment-664166
Share on other sites

My experience has been that when the battery has totally died, and you need to jump start it, you need to have the 'jumper' connected to the 'jumpee' and engine idling for several minutes. The 'jumpee' battery needs at least some charge in it.

Also, the ECU needs something like 7V to activate itself. Cranking on a low battery will reduce the voltage available to the ECU to below the threshhold, and so the ECU will not activate, and if it isn't activated, it can't tell the coils to fire.

And don't forget, most cars have the battery up front, so there's not that much cable between the battery and the starter. The 33 has to get volts all the way up to the front from the boot.

If you can, connect the+ve jumper cable directly to the +ve of the starter motor, and the -ve directly to the engine block.

Alternatively, go and buy a new battery, and you'll avoid the "melted starter cables" syndrome.

Link to comment
https://www.sau.com.au/forums/topic/33004-r33-wouldnt-start/#findComment-665084
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...