Jump to content
SAU Community

5th Gear Rpm

R TUNE
 Share

Recommended Posts

R TUNE Mentor

R TUNE

Posted
Posted

I have a R32 GTST auto and will be changing it to manual soon,

At this point in time the over drive is at 3000rpm at 100km/h, i am wondering when i change to manual what the rpm will be at 80-110km as this is the avg speed i do driving around. i would prefer it to be around 2500rpm for 100km/h.

any one know of any aftermarket 5th gears that are in diffrent ratios or will i have to get a custom one made.

I have the stock diff too.

Link to comment
https://www.sau.com.au/forums/topic/331290-5th-gear-rpm/
Share on other sites
blind_elk Grand Master

blind_elk

Posted
Posted

Why do you think you need to be running that low in the rev range?

Nissan will have set the tune of the engine to be optimised with the gearing of the car. Changing the diff ratios will upset that balance.

Link to comment
https://www.sau.com.au/forums/topic/331290-5th-gear-rpm/#findComment-5380004
Share on other sites
Spurdo Experienced

Spurdo

Posted
Posted (edited)

yea the rb30 would still pick up good from 2500rpm, the old saying "no replacement for displacement" is mostly true.

if your simply after better economy on the highway then personally i dont think it'll happen, if you gear it down to 2500 or so then you'll find you have to spend more time on the gas to overtake (or you may even have to chop it down to 4th, also a good way to use more gas) and even at normal cruising, the rb20 wont maintain 100kph as easily, meaning the throttle needs to open further to maintain 100kph, injector duty cycles go up and fuel economy goes out the window. same reasons why you shouldnt use 5th gear at 50km/h. i'm sure you've tried that. it's shit.

like jiffo stated above, Nissan got it right. there are good reasons why most engines 2000cc and below do ~3000rpm at 100km in 5th gear, it provides optimal fuel economy and optimal driveability. the general rule of thumb for factory vehicles is the bigger the engine, the lower its rpm at any given speed, simply because it can (i blame physics).

and yea, factory diff ratio for auto r32 (2wd) is 4.3. factory manual diff 4.1

Edited by jonboy
Link to comment
https://www.sau.com.au/forums/topic/331290-5th-gear-rpm/#findComment-5384286
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The Bogan
      NC MX5

      By The Bogan · Posted

      The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Duncan
      Who has a Infiniti Q60, Q50 (V37)?

      By Duncan · Posted

      Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • MBS206
      Unpeeling the Orange

      By MBS206 · Posted

      What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...