Jump to content
SAU Community

Recommended Posts

Hey...

Installed a sound system this morning in my R33 GTST.....JL splits in the front....JL two ways in the back....Kicker four channel amp and Kicker box subwoofer.....

Makes a whining sound (matches the rpm)....any suggestions / potential reasons why??

Cheers

Jeremy

Link to comment
https://www.sau.com.au/forums/topic/332777-whining-noise-car-stereo/
Share on other sites

it's called alternator whine and caused by voltage differences and u can hear it as high frequency noise....i.e only on your front splits and not on the low frequency subwoofer.

try this

1. do not run power cables and rca side by side.

2. ground each amp independently and do not attach ground from one amp to the next

3. ground the HU to bare chassis metal...not some aluminium bracket on the inside of the dash

4. if none of the above works...use a ground loop isolator on the rca

i'm no expert in the field...but i have had the same problem before and have always managed to resolve it using the 4 steps above.

Edited by fcruz3r
Hey...

Installed a sound system this morning in my R33 GTST.....JL splits in the front....JL two ways in the back....Kicker four channel amp and Kicker box subwoofer.....

Makes a whining sound (matches the rpm)....any suggestions / potential reasons why??

Cheers

Jeremy

read this and see if any of it makes sense

Noise prevention

  • 2 weeks later...

Alternator whine is likely to be either;

- a poor ground from amp to chassis

make sure the metal is "bright" (get rid of paint by sanding) and that the ring fitting on your cable is making good contact. this includes your head unit ground cable as well.

- a poor ground from battery to chassis

rarely this in modern cars with small systems, but a good idea to upgrade the factory earth with an additional cable equal to the one from your amp to chassis. again, ensure good contacts.

- RCA interference

poor quality RCA's, RCA's that are "coiled" (due to being too long) or RCA's running near engine looms or other power cables can cause noise. easy way to check here is to unplug your RCA's and connect an iPod with a stero jack to RCA adapter. If your noise is still there, it is power side (earthing) if the noise is gone it is signal (RCA) side.

very rarely is it interference due to the head unit itself unless it is older than the hills or crap quality - like sound4 or something :D

If its a pioneer deck then that will be your problem.

what an ill informed comment.

Look pal rather then write the same thing as everyone else has I have given the op another possibility. As unlikey as that will be the issue it does still happen. And yes pioneer decks do have a reputation for being fragile. I am speaking from personal experience.

Look pal rather then write the same thing as everyone else has I have given the op another possibility. As unlikey as that will be the issue it does still happen. And yes pioneer decks do have a reputation for being fragile. I am speaking from personal experience.

from my roughly 25 years in the 12v industry , the Pioneer brand is 1 of the best in terms of features,dependability etc. so your comment isn't valid at all.

from my roughly 25 years in the 12v industry , the Pioneer brand is 1 of the best in terms of features,dependability etc. so your comment isn't valid at all.

lol my comments not valid. :P

You never heard of a fragile micro fuse common to pioneer decks?

pioneers are very well knows to blow "pico" and make whining noise

i had issues with mine and it drove me insane then i put a filter on acc side and it stopped it :)

will take some pics to make it easier and hope this can fix your problem as well

lol my comments not valid. :)

You never heard of a fragile micro fuse common to pioneer decks?

Get over it, you don't know what your talking about, I've installed at least a few thousand pioneer decks etc and never had 1 blow or even a return for problems from bad parts. never.

most issues are install related, bad wiring , shorts, etc

or people dragging to much current from the power antenna wire, use a relay !!!!! or ANY brand of deck will fry

speakers hissing/popping on "deck power" is normally caused by grounded speaker frames to speaker cables or shorted speaker leads hitting the speaker frames common on thin coax speakers, or blown capacitors on crossovers/noise filters

floating grounds thru antenna jacks can as well

Get over it, you don't know what your talking about, I've installed at least a few thousand pioneer decks etc and never had 1 blow or even a return for problems from bad parts. never.

most issues are install related, bad wiring , shorts, etc

or people dragging to much current from the power antenna wire, use a relay !!!!! or ANY brand of deck will fry

speakers hissing/popping on "deck power" is normally caused by grounded speaker frames to speaker cables or shorted speaker leads hitting the speaker frames common on thin coax speakers, or blown capacitors on crossovers/noise filters

floating grounds thru antenna jacks can as well

how bout you prove I don't know what I am talking about rather the spinning shit that you actually work in the audio industry?

it used to do it in my previous car (integra) when my rca was too close to the ecu.

When i pulled it away, then it wouldn't make the whining noise, but when it was closer, then it would come back.

Oh, and it was a very dodgy home audio install. That could also do it!

i also have a kicker 4channel amp

same noise, tried everything

somehtings thats even more strange is the fact i have four speakers connected to the thing yet i only need two RCA's connected for al speakers to work

someone explain that one to me as iv messed around with it lots and yea nothing works im guessing i dont have surround sound i just have two sterio sound

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Given you're running a 2.8 and my 2.5 is not really like for like, I suspect there could be a bit more timing you could give it. What is the kW yield per degree you're putting through it? Here's my E85 map to give you an idea, where it was I could still get another 3~4kW per degree thrown at it.  
    • It turns out that Setrab make a fan specifically for the oil cooler which is great and I've installed it with minimal swearing. I removed my 2x 12in push fans from the front of my aircon condenser and wired them into this. My main thermo fans kick on when I use the aircon anyway and would effectively already be working as puller fans through the condensor which is infront of the rad. The push fans (understandably) didn't really do much in the config they were previously in so now they're out. Now we're on to the "Oil fan doesn't really do much either!". Yes I'll duct it next if it does nothing in heavy use which it shouldn't. But hey, the object exists and fits great and is cool. Let me have this. The car is still in the "do my fittings leak oil now? do my wheels actually rub?" phase. I did a spirited drive on them and didn't hear or feel anything. Then I got back home and noticed there were grind marks on the inside of the rims, though I couldn't see where they were touching I got out the grinder and attacked the suspects. Note: I do not know how to use a grinder. Then I realised I had dragged my new rims across my concrete driveway before I did this drive. I didn't think I had damage at that time when I briefly looked...... but remembered this occurred after I did all the angle grinding. The grinding on the wheels in some very specific spots. It's not around the whole rim for example, which lines up with dragging it across concrete more than hitting a suspension component for even 1 full rotation. So everything is currently painted and taped up and I need to test it some more to see if it really IS rubbing, but from inside the car it doesn't feel like it is. In other news I attempted to do a before and after comparison of the heads/cam upgrade thing. Dynos lie, everything is in different measurements. Here is the data from the sandown back straight. Car go faster than before. Vroom vroom.
    • Here's my base ignition. +3 correction to redline when shooting water/meth which is always on. Looking at my old ignition table, I should be able to add 1-2 degree's next time I'm on the dyno.  Let me know your thoughts. 
    • Given what I know now - same haha, but this was 12 years ago with second hand 740cc Nismo injectors in my S15 daily, I was too busy hunting elsewhere for the issue to even look at the injectors, running through some cleaner was a happy coincidence haha
    • Not a terrible idea. But if I ever had concerns that my injectors were sufficiently dirty to be causing me a problem, they would be out of the engine and onto the actual injector cleaner/testing bench.
×
×
  • Create New...