Jump to content
SAU Community

Wtb Clutch

Sir Lord Van Von Vader'ham
 Share

Recommended Posts

Sir Lord Van Von Vader'ham Veteran

Sir Lord Van Von Vader'ham

Posted
  • Author
Posted

ahhh damn it!

:rofl:

sorry ill call you tomorrow nite bout the seat

yeah, was going to have jim berry make a clutch and he said to grab a 2nd hand gtr pressure plate.

he also said that multi plate clutches are for poser's :(

Link to comment
https://www.sau.com.au/forums/topic/333905-wtb-clutch/#findComment-5412306
Share on other sites
Michele Veteran

Michele

Posted
Posted
missed this post^

he can, but it was going to be $400 odd cheaper...

Did you end up getting in touch with Keith at KB Clutch Engineering in Penrith? He builds an awesome clutch at unbelieveable prices IMHO - you've seen our GTR launch and he built that for under $500 and its still going strong, what was that? Say 2-3 years ago?

I wanted the clutch to be the weakest link in the drive-train and KB agreed with me. He said the only benefit a multiplate would give me over something he could build is 'bragging rights at the pub'.

So mine is a KB built single plate and I love it.

Link to comment
https://www.sau.com.au/forums/topic/333905-wtb-clutch/#findComment-5427445
Share on other sites
GTRKat Grand Master

GTRKat

Posted
Posted
Did you end up getting in touch with Keith at KB Clutch Engineering in Penrith? He builds an awesome clutch at unbelieveable prices IMHO - you've seen our GTR launch and he built that for under $500 and its still going strong, what was that? Say 2-3 years ago?

I wanted the clutch to be the weakest link in the drive-train and KB agreed with me. He said the only benefit a multiplate would give me over something he could build is 'bragging rights at the pub'.

So mine is a KB built single plate and I love it.

Keen to have a feel of this clutch to have something in mind for next time. I haven't seen your GTR launch, what revs are you launching at?

I went the Ogura twin plate and I don't know about bragging rights but I absolutely love it. I couldn't be happier with mine after the punishing I've given it at WSID however I do like the price of yours :D

Link to comment
https://www.sau.com.au/forums/topic/333905-wtb-clutch/#findComment-5427588
Share on other sites
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      S1 rb25/s14 starting problem

      By Duncan · Posted

      Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Waders360
      M35 Brake caliper replacement

      By Waders360 · Posted

      Sorry. Front brake calipers
    • MBS206
      S1 rb25/s14 starting problem

      By MBS206 · Posted

      Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...