Jump to content
SAU Community

Recommended Posts

hi guys hope someone knowledgable can help me out....

iam putting my rb25det into my cefiro as i build the 3ltr bottom end i want to avoid replacing brand new parts eg: mounts or crossmember when the time comes to swap bottom ends i also want to keep the heavier motor as low as possible for a slightly lower cenre of gravity

i need information on engine mounts and crossmember metal mounts ( from block to rubber mount )what combination sits like pics below ?

some say r33 xmember and escort mounts with rb20metal mounts

(but which r33 xmember what series ? and which escort mounts damn it! i need part numbers and mesurements !)

some say ceffy xmember and rx7 mounts again what series rx7 mounts part no's and mesurements

i want this :

kiz1ny8.jpg

or this :

rbs13.jpg

*i have seen this done i dont want to hear about the swaybar hitting the sump or sump being to close to the ground i just want to find out what worked and what combination was used

thankyou

Ben

Link to comment
https://www.sau.com.au/forums/topic/334919-engine-mounts-and-crossmembers/
Share on other sites

mate im putting an rb26/30 in my s15, it is the biggest (highest) u could get, and therefore im using r32 cross member gtst, same mounts, ive heard i could use a 33 gtst, series 1 and 2 are the same, but the 32 sits lower in an s13 14 15.

and of course u have to mod the gearbox mounts anyway

  • Like 1
mate im putting an rb26/30 in my s15, it is the biggest (highest) u could get, and therefore im using r32 cross member gtst, same mounts, ive heard i could use a 33 gtst, series 1 and 2 are the same, but the 32 sits lower in an s13 14 15.

and of course u have to mod the gearbox mounts anyway

the rb26/30 sits lower than 25/30 as the gtr's had front facing plenum and rb25 plenum goes over the rockers

anyway do u have any mesurements for said combination?

Yes your right, I will measure upmy metal mounts when I get time, but I am going to do a practice engine drop in and I'll let u know how I go, I'll measure the cross members and the rest for you aswell

only way to get it where you want it is to modify the engine brackets.

in my S14 i have an RB25 with R33 crossmember and custom cut and shut steel brackets which sit 20mm further back and 20mm lower. works a treat as motor is as far back as it will go and allows room for a clutch fan and radiator. nice and low too.

25/30 in my cefiro I used.

stock ceffy x member, rb20 steel and rubber mounts.

Thats it.

I cut a small ammount of the bonnet bracing away just to be sure, but I think would of cleared regardless.

If you have a picture msg enabled phone, I can send you a pic of how mine sits (only have a pic on my phone)

thanks guys .

im gonna try using rb30 43mm rubber mounts, ceffy brackets and im slotting the ceffy crossmember down 20mm and maybe backwards 20mm we will see.

im not to worried about room for the clutch fan as im using twin thermo's but i believe any weight i can get between front an rear wheels will be benificial i will be doing a write up just to let ppl know because finding this info wasnt easy

ok so ....just posted this on secret drift so i thought id post it here to

in front of me i have:

1x rb25det

1x a31 cefiro :P

1x r33 s1 xmember

1x a31 xmember

2x r33 engine mounts

2x r31/a31 engine mounts

2x r33 engine brackets

2x a31 engine brackets

the cefiro xmember sits mounts on ~ a 45deg angle the r33 sits almost flat so in order to use cefiro (and r32) xmember

u need to use rb20 brackets and mounts which are longer so it sits to high ! approx 520mm above chassis rail

if you use the r33 xmember with brackets and stock mounts which are 78mm this also sits to high

people have said slot ceffy/r32 xmember which i cant see working as the 45deg angle will not let the motor go any lower due to the width bracket to bracket

i reckon u wanna use:

33 xmember

r31/a31 43mm mounts

and 33 brackets.

The 33 crossmember has two holes for each mount so drill a hole in between the two approx 10-15mm towards firewall

put engine in bolt it all together

this should sit top of rb25det plenum just below the strut tops ~470mm above bottom of chassis rail and this should just clear the ceffy swaybar

this would also put the rb25/30det ~505mm above bottom of chassis rail and bonnet will close perfect on a31 r32 and possibly s13 too

also the r33 steering rack should increase lock as from full left to full right the tie end rods move 145mm in 3 1/8 turns

the cefiro/s13 rack moves 110mm in 3 1/2 from full left to full right

so what are your thoughts on this people need some feedback

its a cefiro swaybar, unsure of P/N sorry

got selby swaybars (signature sway bars) on the case, no -one stocks em anymore :P but they have the pattern.

i used R32 x member, r32 engine brackets (shortened) with N1 gtr mounts (ours is as low as possible sump 3mm from xmember, any closer and it rubbed)

Rx7 mounts for fd are pretty common too. similar to simons solution above. i have a few sets of noltec rx7's ones somewhere i will measure up.

nioce work mate :P your quite handy arent ya simon !

but solid mounts on the street will not work for me especially with the drive out to mt tamborine every week to see the folks!!

u can also use r32 gtr front swaybar but will promote understeer without upgrading the rear too

also r33gts25t bars clear the sump and if u use the r33 no mods are needed to fit r33 s2 lca's this will reduce understeer in cefiros/laurels and might be a great upgrade for s13 with heavier rb motor and will in turn give you more lock and more camber

food for thought nissan fans :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...