Jump to content
SAU Community

Where To Buy Body Kits In Wa? (for Skylines Of Course)

johnnnnnyboi

By johnnnnnyboi,
in Western Australia

 Share

Recommended Posts

johnnnnnyboi Enthusiast

johnnnnnyboi

Posted
Posted

heyyyy i just got a question im gonna re-vamp one of my skylines and i was just wondering wheres a good place that sells bodykits in WA? if there isnt one can someone suggest something else like a good online one? also i wasnt really interested in a whole body kit more just a new rear bumper and side skirts... anyway... cheers.

dan_the_man Grand Master

dan_the_man

Posted
Posted

Thread closed. Believe it or not, but since SAU started more than 7 years ago, this topic has been discussed before.

Please use the search function in future. It may be found here:

http://www.skylinesaustralia.com/forums/search.html

While we understand that it can be frustrating to have your thread closed - Please consider that other members may feel it to be disrespectful and selfish of you to post a simple question, without using the search feature to review the wealth of information provided by said members over the years.

If you still feel that this action is unjust, then please PM me and we can discuss it further.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • GTSBoy
      Nissan fuga 450gt android screen

      By GTSBoy · Posted

      What about if you just give it direct 12v and earth?
    • The king 2.0
      Nissan fuga 450gt android screen

      By The king 2.0 · Posted

      Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • MBS206
      NC MX5

      By MBS206 · Posted

      My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
×
×
  • Create New...