Jump to content
SAU Community

Recommended Posts

My gearbox was crunching into second, doing a bit of research i found that an oil change helped ppl alot.

So i change my oil to castol epx8090, didnt really help.

When cold its hard to change into second, as in the gear stick is hard to push in. This is only when cold, with the old oil it was fine.

I guessing my box is worn? but is there any additive or even another oil change you can recommend?

I'm not recommending it, though I read people add the Nulon G70/G90 (not sure on the model) additive when changing their gearbox fluid. Since you don't have a GTR and no transfer case, you could add it through the shifter instead of taking the filler plug off the side of the transmission.

Reco, and yes if you want to do it properly you get it reconditioned. Once you crack open a box and start replacing parts you upset tolerances and other parts.

A recon price varies on how much you want fixed, if you only want 1 sychro fixed you get charged for one synchro, you get more replaced you get charged more. All depends on what is found when your reconditioner pulls the unit apart. Could be 1k could be more

  • 2 months later...

My R33 GTR also has the occasional crunch into 5th gear. Why fifth?

just the way it goes sometimes. it is odd though, the synchro mesh on 5th doesnt usually get anywhere near the thrashing that 2nd-3rd-4th does. although i used to have the same issue but it turned out my clutch fluid just needed to be bled, lol. not sure why it only affected 5th.

just change the box oil to redline shockproof, see if that helps

  • 2 weeks later...

Thanks for the response. I have already changed the oil since I posted my issue. It hasn't crunched since I put it in. I used shockproof light. It had also crunched on one or two other gears, but it was just the odd one. I checked my brake fluid and the level is ok. Even if there was a bit of air in the system by the time you get to 5th, it's been pumped a few times. It should really be crunching when selecting first after being stationary out of gear. or cruising for a while before a gear change. I'm hoping this Redline (smurfs blood) has solved/covered-up my crunchy problem.

Just to share, I had a similar symptom on my R32 GTR (77,000km) that lead to a transmission replacement.

I had a crunch in 4th, and eventually developed a crunch in 3rd at high rpms. I switched the fluid (nothing special) in hope that a fresh fluid would help eliminate the crunch but it just made it more prominent.

Anyways, I have yet to find a permanent solution to the synchro issues on the R32 transmission, and it seems like no one has ever found one. I have been reading that even the R33 boxes have similar issues.

I know I am going to have to replace the box again at some point in time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
    • My experience with Rising Sun Exports Before agreeing to the sale I tried to do as much research as I could (obviously), his Facebook reviews are 98% and he goes Live at least once or twice a week. I contacted 2 people in the UK who had used him for their imports, both had positive feedback. His explanation and talk through of the import process was thorough, answering any query no matter how stupid it was. It felt as soon as the money was sent, communication dropped off. I asked for shipping updates every 2 weeks or so, not wanting to pester him, he never had any updates. I wasn't informed the car had been dropped off at the port, I only found out by his Facebook story. I asked for the photos taken at the port, knowing he would need some for insurance purposes. I received a few 5 second clips and that's it. When asked again, he said his staff had them. Weeks later I asked again, he tells me he doesn't have any, but does have 50 photos from the original advert. I never received them. I eventually got the documents sent via WhatsApp after I mentioned the port was requesting them. I purchased a CarVX report, to find out the vehicle is a Grade R with recorded accident damage, first recorded in 2017 when it was first auctioned. He never told me the grade, then again I didn't ask. His response was "Grade R means nothing, it wasn't chassis damage". Still, I would have liked to have been informed about it. Jon prides himself on being open and honest when it comes to inspecting cars, it's his main job doing so at the auctions for customers. When the vehicle arrived in the UK I noticed a few little cosmetic issues. It's a 21 year old car so it wasn't going to be mint condition. The side skirts are cracked on each corner and the sealant is failing. The front grill on the bonnet/hood isn't secured very well, mounting studs are missing. Both minor things, but again, it would have been nice to be told. During a Facebook Live walk around video of the vehicle, he mentioned it has a front Whiteline anti roll bar/sway bar. While on the inspection ramp, I noticed the stock item has been installed. When first questioned, his response was "the ARB? Switched? Since when, it never had them". Since sending video and photo evidence I've not received a response. I'm probably being over critical of the overall condition of an old car, but all I wanted was honesty (which he claims to have). I'm aware I wasn't his only customer, he's busy doing XYZ but other reviews praise him for great communication with regular updates and photos, I felt I didn't receive the same treatment. 
×
×
  • Create New...