Jump to content
SAU Community

Carbon Fibre S2 Front Foglight/indicator Surrounds Group Buy!


Recommended Posts

Hi Guys,

I just wanted to thank everyone for the patience and understanding in this group buy.

I am very proud to say THEY HAVE ARRIVED!! I am busy packing these up for you all I will have them in the post tomorrow with delivery before the weekend.

You will receive an email with your tracking details tomorrow.

Thank you again to all of you.

Cheers,

Shane

PSI Parts

  • Like 1

Ok, I have been to the post office and they were all sent Express Post so expect them tomorrow guys.

You all should have received an email with your tracking details also.

Shane

managed to snap off one of the screw points while fitting.. im raging so hard right now lol

hopefully an adhesive helps..

Oh man that sucks. I was so paranoid about doing the same thing. Try some hardcore superglue or just don't worry about the one.

My stock ones had two snapped off from a minor prang with a roo years ago and I didn't even know about it.

wow Phil i cant believe how dissapointed i am right now with the fitment of these, i go to put the right hand side 1 on first and 3 out of the 6 tabs are about 5mm out of where there supposed to be and are no where near fitable, all the tabs on the right surround are overly to fat compared to the left side surround where the tabs all look beatiful and alot neater. i know with being aftermarket and carbon there not going to be 100% but to completely not line up is not cool.

Been waiting so long for these and for them to not fit is so dissapointing, i dont want a refund would just like a set that fits!

  • Like 1

If you have a drama send us an email with a pic and an explanation with what the drama is and we can sort it out.

Hmmm that's strange man. Mine were nearly all spot on. A couple needed a slight "push" with the screwdriver to move them a millimetre or so, but nothing that would make it not fit :(

i glued the mount back on but ended up just ignoring it since it didnt really influence the fitment

regarding fit, i found it was out a bit too. 2 points on each cover require the mounting point to slot inside, and the points on this cover are just too fat to fit inside the little circle on the foglight assemply

i ended up just trimming about 5mm off the 2 points on each cover. just used a hacksaw blade took about 10mins

agUul.jpg

MW8Hy.jpg

  • Like 1

I wonder why mine didn't have any problems? Like I said, a couple of the screw holes were slightly aligned wrong but only by maybe a mm. And some of the holes were drilled slightly to big so I just needed slightly thicker screws but that was it.

Delljit, looks good man. You happy with it?

well i had to use wider screws, and the 2 mounting points that are closest to the centre of the car were too long to fit into the assembly's standard points so i had to hack saw a few mm off to compensate

it looks good but was a bit more screwing around than i initially anticipated

happy with the end product in terms of appearance, not as happy in terms of needing adjustments

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...