Jump to content
SAU Community

Recommended Posts

  • Replies 407
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

AWWW SHIT, been busy today running around and trying to work out a price guide for shoots. Not to mention I didn't get out of bed til like 1130 :( Haven't done that for agggges!

I'll PM you a link so we don't clutter this place up. Here's a couple

DSC_8462.jpg

DSC_8561.jpg

DSC_8655.jpg

DSC_8700.jpg

Thanks for sendin the link. Will check it out properly soon :laugh:

I like that first shot of them and that first guest shot of him smoking. Some cool pics in here. So what did you think of wedding photography? harder than it looks uh!!

It was difficult to try and capture the moment without creating the moment. It was made harder by the fact that i was trying to be invisible to the real tog, and also because I spent more of the night with a glass in my hand instead of the camera hehe. I think i got a few good shots off though which is more than I expected shooting from the shadows. there's definately an art to it.

You've done an awesome job on that one. I'd maybe brighten or change the curves on the front of the car to give a bit more seperation but apart from that I really like what you've done. looks evil!

I have a really awesome printer out here (Person, not a canon haha) I love how different good shots look off a screen. I've printed a few car shots recently, I think I'm going to have to many prints soon :P But I'll still be getting this one done, just to see how it looks.

Havent posted in here for ages. Had to sell my DSLR gear to pay some debts but couldnt handle not having a camera so I bought a Panasonic Lumix FH1. Its cheap and the lens has some nasty softness near the edges, but it will have to do. Best thing about it is its light and easy to carry around which has actually increased the amount of pics I have been taking. Anyway, I'll link as thumbnails as there are a few from this month, so click on them if you wanna see the larger versions.

Graffiti Shots: (most of these i wouldnt have taken with a DSLR as its a pain to carry around, specially in tunnels and stuff)

20101001-172438.thumb.JPG 20101002-154314.thumb.JPG 20101005-115306.thumb.JPG 20101005-115534.thumb.JPG

http://photos.jay019.com/graffiti/

Light Painting: (a couple from late last month, meh)

20100926-201637_E.thumb.JPG 20100926-202646_E.thumb.JPG 20100928-004106_M.thumb.JPG 20101005-232405_M.thumb.JPG

http://photos.jay019.com/random/

The new family bus:

20100926-091611.thumb.JPG 20101005-122144.thumb.JPG

http://photos.jay019.com/e50_elgrand/

And thats about it so far. Will be mostly concentrating on light painting pics as they are pretty fun. Wish I had a bit more control over exposure, but ah well, least I have some kind of outlet, lol.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...