Jump to content
SAU Community

Recommended Posts

I got my Skyline early September and it came with a Kakimoto Regu 06 & R.

Its a full Turbo back exhaust, I have done some research on this exahust system, and most people say its very quite until you rev the engine. I find it quite loud and the cops have pulled me over a couple of times and question me about it. :huh::D:):O Most cops just let me off with a warning telling me to change the exhaust system. I drive this car as a daily so cop trouble will be normal.

Every time a cop ask me about my exhaust, I told them that was how the car is when i got it from japan. I just want to know what peoples opinion on this exhaust system is. Like i mention when I did some research and people always say that this exhaust system is suppose to be quite on low RPM.

If its because its a turbo back, that is why its making so much noise, would you think it be a good idea to change it back to cat back or you think its a stupid Idea. :):geek::geek::geek:

Link to comment
https://www.sau.com.au/forums/topic/339046-opinion-on-kakimoto-regu-06/
Share on other sites

  • Replies 61
  • Created
  • Last Reply

Top Posters In This Topic

A friend had one on an evo 9, was very quiet running around and let out a loud shriek like it was gating when booted.

Bare in mind this was with a factory dump and next to new/working cat.

and this is why its so quiet...

it's exactly like having a weld in silencer, with < 2 inch exit...

the photos are taken from a newer version of kaki N1, but i think the regu 06 is the same on the r33, not sure about r34, and this exact same design also applies to the rear cannon of R34 GTR super Ti from fujitsubo

thing is, you can't have a cannon style muffler and be quiet without restriction. its just not possible, even if you have a oval resonator in the middle

so if you have a quiet cannon, have a look inside and this is what it's most likely going to have

post-27668-1286105372_thumb.jpg

post-27668-1286105706_thumb.jpg

Edited by chiksluvit
there is no restrictor in the 32gtr regu

and ive sat next to cops and driven past them like an arab on a carpet

ahh that makes sence when i was looking at them pics above i was thinking theres noway my cannon has that in it

Yea, mine definitely doesn't have a scilencer and its a great exhaust. Quiet for when cruising but just right for when you boot it. Cops have never given me any grief. Maybe its not the regu 06&R. Im sure Kakimoto make more race orientated exhausts which would be much louder.

hrm that one in the photo's definitely for turbo r33, its Kakimoto N1 +REV, part number's N31307

same part number for GTST & GTR, 3.5 inch piping

it was ridiculously quiet for 3.5 inch cannon exhaust so i thought i'll check it out, and that's what i found

so i assumed that the regu 06&R probably shares the same design seeing that people say its quiet, thought i haven't heard one on an R32/33/34 in real life

then i thought about my friend's r34 GTR with the quiet fujitsubo, had a look inside and found the same thing

the r34 pulled 260rwkw with that exhaust, PFC and boost controller, and 30,000km but the engine blew after a track day, rods came out from the side of the block

we couldn't figure out why, until i read this http://www.skylinesaustralia.com/forums/Da...er-t314520.html so i guessed that this might be a contributing factor

Guys I dont have a silencer as well on mine exhuast i take a picture tonight and post it online. That is most likely why i find it so loud or unless the moron in japan only used the muffler of the regu 06 and did custom piping i take a picture of under the car aswell. I am more of a newbie at this sorry guys.

good to hear that the regu 06 doesn't have that silencer thing welded in like the N1+rev, in that case it's a much better alternative over the N1 and some others like fujitsubo super ti

last time i checked i think Blitz exhaust also shares simillar design, except the silencer opening is a lot bigger than the Kaki N1 +REV

FYI The old kakimoto hyper 2000 N1 or HKS silent hi power and old Apexi n1 don't have it, but they're really loud

Edited by chiksluvit

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Possibly avoid using a Cometic one unless the deck/head surface are perfectly flat. I did have a look just then and forgiving gaskets such as Tomei or Nitto don't exist for the FJ20, however the Bar-Tek or Kameari ones look good and might do the trick.
    • Because pipe threads for pipe things. M threads for bolt things. Throw some teflon sealant onto it and dust your hands off knowing you did the right thing, instead of going twice around the block to achieve a result using the wrong things. Of course, all of these solutions are ignoring the fact that the minimum thread pitch we're talking about here is 1.25mm, with the 1/4" in NPT or BPS being out around 1.4mm. You will need to know that the boss you're tapping has enough thickness for at least a few threads. That's one of the reasons that 1/8" is commonly used - because the pitch is <1mm. And why would you look to use 1/4" NPT in a BSP country anyway? Ugh.
    • Just throwing around ideas, does it need to be in the compressor cover? Why not the hot side piping?
    • 1/8NPT drill size = 8.7mm. Since the hole got messed up by me, it’s probably around 9mm.    So 1/4” NPT would be next step. A drill size of around 11mm would be preferred there which is not way of my M12 (drill 10.5mm and tap M12 threads) 
    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
×
×
  • Create New...