Jump to content
SAU Community

Very Odd Gtr Oil Cooler

Kaido_RR

By Kaido_RR,
in Engines & Forced Induction

 Share

Recommended Posts

StealthX Veteran

StealthX

Posted
Posted

Dude, that's sick! doubles as a strut brace by the looks of it! I wonder if it lacks strength because it has hollow cavities for oil cooling?

Imagine taking a tight corner, putting stress on the strut towers and then it cracks, pissing oil all over the top of your engine hahah

Beer Baron Grand Master

Beer Baron

Posted
Posted

yeah it's just an oil/water heat exchanger. to make the most of it you'd need a larger than standard radiator or a second smaller radiator to cool the coolant flowing through it. they just chose to make it look fancy and mount it on the strut brace. no way would you buy it for $1000.

for similar money PWR will make you a GTR radiator which is twin pass and has an oil cooler/heat exchanger built into it. used on may serious track cars. very effective in that they also help bring oil up to temp and then keep it stabilised at operating temp. so then you're getting a better radiator AND the oil cooler for the same money.

The Dan Grand Master

The Dan

Posted
Posted
yeah it's just an oil/water heat exchanger. to make the most of it you'd need a larger than standard radiator or a second smaller radiator to cool the coolant flowing through it. they just chose to make it look fancy and mount it on the strut brace. no way would you buy it for $1000.

for similar money PWR will make you a GTR radiator which is twin pass and has an oil cooler/heat exchanger built into it. used on may serious track cars. very effective in that they also help bring oil up to temp and then keep it stabilised at operating temp. so then you're getting a better radiator AND the oil cooler for the same money.

Spot on!! :P

Beer Baron Grand Master

Beer Baron

Posted
Posted

forgot to mention that it looks to me to be a laminova type core. they make special cores for turbo engine pipework and also make sealed oil/water heat exchangers/stabilisers. very interesting type of core and apparently quite efficient.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
yeah it's just an oil/water heat exchanger. to make the most of it you'd need a larger than standard radiator or a second smaller radiator to cool the coolant flowing through it. they just chose to make it look fancy and mount it on the strut brace. no way would you buy it for $1000.

for similar money PWR will make you a GTR radiator which is twin pass and has an oil cooler/heat exchanger built into it. used on may serious track cars. very effective in that they also help bring oil up to temp and then keep it stabilised at operating temp. so then you're getting a better radiator AND the oil cooler for the same money.

What diameter pipes do they use? I had thought of getting a filter relocating kit and running it through the heat exchanger in my auto radiator (have converted to manual). Then if I need a bigger radiator at that point I could add a proper oil cooler and thermostat.
Kaido_RR Grand Master

Kaido_RR

Posted
  • Author
Posted
Anyone have the yahoo link?

http://page21.auctions.yahoo.co.jp/jp/auction/j94861066

i found it again, looks like it didn't sell at the price of 89,000yen so the started the auction again at a starting price of 1yen with no reserve.

pretty cheap atm, about the same cost as a strut brace might bid of it for some giggles

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      sold listed as a Tomei LSD 1.5 Way For 1998+ Nissan Skyline ER34 25GT RB25DE w/Open R200 https://www.ebay.com/itm/174006114594?campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=&mkrid=711-53200-19255-0&loc_physical_ms=108689&loc_interest_ms=&campid=5338967980&mkevt=1&mkcid=1&toolid=10050&customid=71883f2ccc571356e0a757bc7adfdde2&mkrid=710-53481-19255-0&loc_physical_ms=108689&loc_interest_ms= it went in like butter all gears, alignment, back lash etc, rotation and clearances correct, and if rolling all rotates smooth and free when coasting down road , clutch in or out over 10 mph smooth... its the binding, clunking and jerking from a stop that is most concerning, also seems like its going to tear the tires off in 10 miles of normal road driving. 
    • Kinkstaah
      new 1.5 LSD issues/concerns

      By Kinkstaah · Posted

      What 1.5 way? There's no such thing really as a 1.5 way, just different ways of explaining 2 ways with different ramp rates. HOWEVER. In any driving in a straight line your 1.5 or 2 or 1.7 way should have no clunking at all. With the clutch fully depressed the diff should be silent (unless it's welded but I'm assuming it's not). Something aint right here.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      Clutch is a spec brand, new clutch system,( PP, flywheel, friction disc, etc. pull type) installed 100 miles ago, with no problems.
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drove beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Matt Z
      SAU NSW - Archies Flame Grille Meet & Cruise to Kurnell

      By Matt Z · Posted

      Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
×
×
  • Create New...