Jump to content
SAU Community

Recommended Posts

I'm after a standard 260RS MOMO steering wheel...

Anyone got one for sale or know where to get one?

I've checked import monster but they're a bit pricey on there.

Also on a side note, anyone know how a set of 19x9.5+22 wheels will sit on a 260RS? They have the bigger brake clearance aswell... (Rays GT-Cs)

thanks guys

i run 19x9.5 +27 (rays gt-f) on the rear of my 260rs and i have 2 run 6mm spacer to keep inside of rim from rubbing on my hks coilovers hope and sit dead flush with outside of car hope that gives u an idea and that big on front may not sit rite

Edited by 260rsstagea
Is the one you're after, the factory momo one with airbag?

I may be able to help you, what price is import monster after/what are you willing to pay?

:laugh:

I have bought a couple of these

Last one was 100% mint for less than $350 del from japan

R34 uses the same momo wheel, along with a few other jap cars we do no see here

Not hard to find on Yahoo auctions

Edited by darrinspencer

Yeah after the airbag one. They've been around the $300-$400 mark.

What other cars Darrin? I've found a few that look identical but wasn't sure if they'd fit, was thinking about going 34GTR if I couldn't find a stag one.

  • 2 weeks later...
I have bought a couple of these

Last one was 100% mint for less than $350 del from japan

R34 uses the same momo wheel, along with a few other jap cars we do no see here

Not hard to find on Yahoo auctions

Oooh how do I buy??? Lol

IMO buy the R34 version of the momo wheel for your 260rs. Do you have paypal? Shoot me a pm and i will run through buying with you. Remember to double the auction price for delivery ex Japan. :rofl: If you dont want to wait 2-4 weeks to get the steering wheel from Japan, there is a R34 GTR wheel for sale somewhere here.

Edited by dirtyRS4

The R34 momo wheel I tried on my S2 fit fine (airbag & tiptronic controls too) but it was smaller than stagea wheel, and had the R34 3-spoke design (as opposed to the stagea 4-spoke design). Just something to keep in mind; I'm pretty sure they're not exactly the same (but will work, are very similar, and some people might prefer the smaller R34 one).

The R34 momo wheel I tried on my S2 fit fine (airbag & tiptronic controls too) but it was smaller than stagea wheel, and had the R34 3-spoke design (as opposed to the stagea 4-spoke design). Just something to keep in mind; I'm pretty sure they're not exactly the same (but will work, are very similar, and some people might prefer the smaller R34 one).

As I've said before you can use s15, R34 GTT and R34 GTR, connectors for airbag and horn fit. Be careful with clock spring and pull the fuse. Smaller, sportier feel and less boat like. They are all relatively the same and cascade usually in price depending on model.

R34 GTR steering wheel

Edited by dirtyRS4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • looking for some help and maybe some insight on others experience with a new LSD. R34 GT ran and drive beautifully, but always alot of grip loss due to the open R200 rear end, so I just installed a new 1.5 LSD way into the stock open R200 for a ER34. Simple. Everything seemed right. I test drove for the first time this weekend. as I started to back out the garage the first time slowly with tires straight it sounded and felt like I had a loose or half disconnected drive shaft...that was clucking around loose and shaking entire vehicle, and making it feel like the trans clutch was spontaneously slipping then grabbing very roughly while just letting out pedal slowly. I backed it out went to pull forward with the same noise, shake and slip grab feeling with hesitation, I turned the tires to back out more and then pulled ahead some same thing but worst because of added wheel resistance (which that I expected) puzzled … pulling it back in checking everything over and finding nothing wrong, I tried it the next day. same thing, couldn’t believe how it shook everything again making a terrible noise and making it feel like the trans clutch was slipping and grabbing, but I got it out of garage into the driveway, got it straight, drove forward and then reveres a few times in a straight line everything shaking , causing what felt like clutch slip and grab every time, sounded like right behind front driver tire and I could feel it in the floor board with my feet,... worst right when beginning to let clutch pedal out to engage slightly, shuttering and sounding terrible along the way…I managed to slowly get down the road, babying it the whole way, once I was rolling (out of 1st) seemed to be better and between shifts, then clutch felt closer to normal…not slip/ grab etc., but back down to any stop, straight road or turning, same thing. Made no difference if all tires were straight or if I was turning. All other gauge read out correct. with in 2 miles as planned I reached the empty parking lot and performed the break in procedure that came with lsd, essentially to drive in a figure 8 a bunch.  Did this, binding chattering, and shaking the car the whole way. I drove it back home seemed somewhat normal once I was in straight line and past 10 mph or so, and I know it will “bind” on corners and cause some tires squeal when turning especially from a stop, but when I begin to move it still causes what feels like the trans clutch to slip and jerk badly as well as shaking the entire car, and sounds terrible, that I didn’t expect. I used the fluid they supplied with LSD kit and did the breaking, planning to change fluid as they suggest after breaking, but wondering will it get smoother or less aggressive with use? maybe a 1.5 is just too aggressive for normal road driving?   I have a LSD that I put in my 71 cuda when I restored it, with amazing smooth , quite yet effective results. Different style LSD but that ones a joy to drive. maybe expecting too much from this R200?
    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
×
×
  • Create New...