Jump to content
SAU Community

QLD Whoretown...

predator

By predator,
in Queensland

 Share

Recommended Posts

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Popular Days

Top Posters In This Topic

Popular Days

strutto Grand Master

strutto

Posted
Posted
10psi according to the previous owner and the boost guage 0.7bar

Haven't had it long enough to get ot on a dyno

But the SAFC is tuned ATM right? I'm not overly confident tuning it further without having some idea of what the fuel curve is like at the moment...

You may be best to just keep the boost at 10psi once the dump is done...

Lazy-Bastard Grand Master

Lazy-Bastard

Posted
Posted
But the SAFC is tuned ATM right?  I'm not overly confident tuning it further without having some idea of what the fuel curve is like at the moment...

 

You may be best to just keep the boost at 10psi once the dump is done...

Yeah it is tuned atm and seems pretty good.

Do you know if the boost will rise as a result of the dump pipe?

Having said the tune seems pretty good, I wouldn't know the sound of pinging if it bit me on the ass :blah:

strutto Grand Master

strutto

Posted
Posted
Yeah it is tuned atm and seems pretty good.

Do you know if the boost will rise as a result of the dump pipe?

Having said the tune seems pretty good, I wouldn't know the sound of pinging if it bit me on the ass :blah:

Depends on how good your boost control is... If your using a good EBC, it should be able to keep the boost at what ever level you choose... A bleeder on the other hand is more likely to allow more boost to be produced... Should be able to get rid of any extra boost though depending on the bleed...

Pinging sounds like a rattle in your engine bay... Best way I can describe it... I was chasing down an engine bay rattle for 3 years on a Turbo Laser with no intercooler, blow through carby and 22psi before I worked out what pinging was... :D Oh to be young again!

All posts are guaranteed... Guarantee is not a guarantee... :rofl:

Ska Grand Master

Ska

Posted
Posted

Nice, but are you watching it with a good home theatre system, if not, it just is not the same, need at least a billion watts of speakers pointed at you all going full blast to get the best experiance out of the matrix series :rofl:

Lazy-Bastard Grand Master

Lazy-Bastard

Posted
Posted
Depends on how good your boost control is...  If your using a good EBC, it should be able to keep the boost at what ever level you choose...  A bleeder on the other hand is more likely to allow more boost to be produced... Should be able to get rid of any extra boost though depending on the bleed...

It's a Hybrid EBC...seems to hold pretty steady, doesn't spike over0.7 bar

Pinging sounds like a rattle in your engine bay...  Best way I can describe it...  I was chasing down an engine bay rattle for 3 years on a Turbo Laser with no intercooler, blow through carby and 22psi before I worked out what pinging was... :D  Oh to be young again!

I had a Cordia turbo that was apparently pinging its tits off....didn't realise until a friend who was a marine engineer brought it to my attention....had been thrashing it in that state for over a year so promptly sold it to an unsuspecting Lebanese gentleman (I use that term advisedly)

All posts are guaranteed...  Guarantee is not a guarantee... :rofl:

Nice disclaimer :D

pimpspec Mentor

pimpspec

Posted
Posted
So you need a boost constoller to run the bleed valve

I was under the impression you just split the line, pop the above bleed valve and loosen it for more boost?

like i said before ... a bleed valve is a boost controller. put that in you line between your actuator and comp cover or inlet pipe depending how its setup .... if your still having troubles i suggest you pay someone or get someone who knows about it there when you do it, that way there's no risk of something going wrong ..... bet you really don;t want to fork out for new pistons hey ...

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      So either way it is gearbox out and look what is wrong?  I know about the input shaft bearing. Even before swap/new clutch the it sounded exactly like this: So is that inout shaft bearing or the other was installed backwards?  And can some please tell me the part number for that input shaft bearing? The gearbox is small box from R34 N/A and number is FS5W71C. Thank you  
    • Kinkstaah
      My BMW 335i

      By Kinkstaah · Posted

      I am yet to see anyone ever regret a quaife or helical. ...other than drifting/skidpan duties. I kind of want to upgrade my factory helical with a Quaife (but really it's not ultimately that different, and is a MASSIVE UNDERTAKING), that's how good the hype is about them, that I want to try them 'just to see'  
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      D2 and Ksport are essentially the same thing and basically just generic Taiwanese manufacture. Better than ChinaBay crap, but... not top shelf. Öhlins have got to be some of the best dampers around, so likely to be a good option. It's going to get to the point though where I suggest you buy from Oz. We have at least 2x excellent options here. If I were you though, I'd be talking to KW about doing something for the R33. There's bugger all difference between that and the 32. In GTR land, anyway.
    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      KW only offers a set for the R32 GTR. Popular options are D2 racing, Ksport or Öhlins. I have a D2 Racing coilover set, though I don't know for sure which one.
    • GTSBoy
      Unpeeling the Orange

      By GTSBoy · Posted

      Well, the good news is you have more than one very good option for new coilovers in and around your country. Worth the drive over to KW to talk about GTR stuff.
×
×
  • Create New...