Jump to content
SAU Community

Recommended Posts

its a good idea to replace the tensioners.. was yours stuffed cyrus or he just thought it was a good idea?

mine i am not keeping much longer so i don't really care about longterm viability so much.. as long as it doesn't pack it in in the next 10,000km thats all i want. .

  • Replies 62.7k
  • Created
  • Last Reply

Top Posters In This Topic

  • chaos

    7164

  • Ska

    5791

  • BelGarion

    3645

  • Nexus9

    3590

Top Posters In This Topic

So I have to scan them?
well i scanned each page in off the refidex.. then imported into photoshop, matched, resized.. etc

Oh MAN why not just use the UBD on cdrom, dats whay I do :), way eiser than scanning!

its a good idea to replace the tensioners.. was yours stuffed cyrus or he just thought it was a good idea?

mine i am not keeping much longer so i don't really care about longterm viability so much.. as long as it doesn't pack it in in the next 10,000km thats all i want. .

Well one is stuffed and Gav said it owuld be best to replace both at same time, I still have both of them, I thought hell I have paid for them, mine as well kepp em, might bring them along next time I am out :D

Cyrus, congrats, ur now in charge of sending me the maps off your CD :D

you got broadband I'll just email you the cd :D:)

I can post on to you if you want, they are only like $30 and this new version you get all the cities, even perth! :D

There's not point using map references because every refidex's pages are different.

Are they? I thought they at least tried to keep the same ones as best they could. UBD always did suck though.. nobody used them in melb - they all used melways.

CD rom sounds like the best way!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Working through possible solutions of converting my mechanical speedo.    Anyone know what type of speedo sensor the factory r34 gtr getrag has ? what the output is ? I assume its not a VSS and more a voltage like earlier speedo sensors ? Can an ECU read it ?  
    • roof rail delete used to be a thing, they were made locally for a while too
    • I can get more photos of it here soon and I plan to make a thread detailing the process. I received the car this way and it sorely needs refinishing. That is probably the most appealing photo of it. Up close it is fading, cracked, and needs to be re-glued. Depending on their condition I'm on the fence between refinishing or making a new set.  Another angle hiding the pimples and razor pumps  
    • According to this thread the RS4V with build plate RC40 comes with the R200 diff @ 4.083 ratio as well (mine has said RC40 denotation). We may need to check if the axle stubs are the same pattern as well. The auto subframes have longer axles. However I think yours being a later Series 2 as well, we should have the same bolt pattern for the diff stubs. Unless your upgraded rear also has upgraded axles. Either way, I would not be opposed to pulling the covers to check so I can inspect that  fancy rear core  Also I don't have HICAS. I don't believe that should change things but I hope the people here with heaps more experience than me can correct me if I'm wrong   Let me know if you want to attempt to make this work and I can get some pictures of mine from under the car. 
    • It's not that straightforward. For example I have had this code because my ignitor/power transistor wires were unplugged. It knows something is wrong but has no idea what it means. If you want to actually diagnose this I recommend following the service manual flowchart for code 21. Ohm out the harness, coilpacks, inspect the ECU, etc. And again, it's entirely possible for there to be no problem at all but if you're running a different coilpack it'll trigger the code because it doesn't like what it sees.
×
×
  • Create New...