Jump to content
SAU Community

Recommended Posts

Well, i might be going back to the world of car ownership if all plan's fall into place.

So i'll need my own car (and it won't be diesel or Toyota!).... so it's time to jump through the car finance hoops.

So my question is.... who has what, dealt with whom, and who is just all around ace for car loans.

:(;):banana:

Link to comment
https://www.sau.com.au/forums/topic/343812-car-finance/
Share on other sites

depending on how long a lease you want,

make sure you cop everything up front, you don't want to have a massive balloon when the time comes to sell your car..

because if the balloon is too high you'll have to put an exuberant price on your car which no one will take...

3 year lease with 30% residual should be good.

Link to comment
https://www.sau.com.au/forums/topic/343812-car-finance/#findComment-5542944
Share on other sites

Hi,

My wife works for a finance company and used to work for a car finance broker for years, so can give you some basic advice. So i will now hand over the keyboard.

Hi guys. Most finance companies dont like imported vehicles for various reasons, however you may find some lenders who will consider an application depending on your profile. eg. some have the following conditions: Must be a homebuyer, contribute large deposit ie. 30% and a shorter loan term of say 36 months. If you go down the broker track bare in mind that you will be charged a brokerage which for some brokers can be anywhere up to $1000. There is an option of an unsecured personal loan through a bank but then that also depends on variables such as how active your credit file is, stability in residence and employment, and whether you have conducted your account well eg. have not overdrawn it in the last 3 mths.

Just something to think about....

Link to comment
https://www.sau.com.au/forums/topic/343812-car-finance/#findComment-5543169
Share on other sites

what car you looking to get?

car finance you cant beat bmw finance also known as alphera (spelling) basically only ones without exit fee's and stuff but yeh if you go like personal loan interest rate is ALOT higher but as said above usually comes with "balloons" on finance but depends on your situation. advice is usually free just call someone up

Link to comment
https://www.sau.com.au/forums/topic/343812-car-finance/#findComment-5543344
Share on other sites

I would say BMW Alphera is great to deal with.That's who holds the finance on the Lancer, after I sold the car to my mum she kept the finance with me cos I'd had no problems with them.

*No balloon

*fixed interest

*they're happy to DD or for you to pay by Bpay

* Happy for you to pay extra with no fees

*No exit fees

*There pretty flexible if you can't make the payment, just ring with 2 or so days notice.

*Online account so you can check how much is left owing and anything else you need to look up

the catch?

They won't finance cars more than about 6 years old, and weather they like imports I don't know

Link to comment
https://www.sau.com.au/forums/topic/343812-car-finance/#findComment-5543812
Share on other sites

Secured loans (car loans) generally aren't available for cars over a certain age. The age varies between lenders. I've had unsecured personal loans on two of my cars. The interest is higher but I pay them off quickly so meh.

Link to comment
https://www.sau.com.au/forums/topic/343812-car-finance/#findComment-5544604
Share on other sites

Have done a number of these over the years so my 2c:

Evo VII was through Esanda. They were ok and accepted it being an import.

Evo VIII MR was also through Esanda as they had everything on file (had changed jobs but kept it as my previous one).

Cooper S was through Alphera as bought it from BMW

S4 through Alphera as BMW had all details.

I can't stand wasting time and sitting on a phone/faxing/scanning docs is a pet hate. I juggled the residuals with them and it will depend on whether you intend to keep the car long term. If you take it over 3-5 years and put a high (ish) residual on it, payments are lower and when you sell, you pay it out. This is good if you need surplus income each month. If you want to keep it long term, make the payments higher so you are not hit with $5-$10K + balloon at the end.

Also looked at novated options (drawing on Ferni's expertise) but instead just claimed the business usage seperately.

VII's are good value now, looking again myself. S4 for grabs if interested :D

Link to comment
https://www.sau.com.au/forums/topic/343812-car-finance/#findComment-5544672
Share on other sites

I'm thinking a good ole fashioned car loan...i own the car at the end of it.

Should I go the broker route or Google the shit out of it?

Go to a Broker.

I work in the industry and I can tell you a good broker will get you the best deal.

Macquarie are doing pretty good car finance at the mometn but you'll only get it through a good broker.

Try and find a broker who is Accred with Connective. They are the best in the business.

Link to comment
https://www.sau.com.au/forums/topic/343812-car-finance/#findComment-5544975
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...