Jump to content
SAU Community

Recommended Posts

yeah, i'm taking the R,

the girlfriend is actually visiting a friend, who's also a scottish fold breeder, to view the kittens, and then since we're already there, was just wondering what to do..

nice roads eh? =D~~~~~~~~~~~~~~

yeah, i'm taking the R,

the girlfriend is actually visiting a friend, who's also a scottish fold breeder, to view the kittens, and then since we're already there, was just wondering what to do..

nice roads eh? =D~~~~~~~~~~~~~~

most roads in adelaide are truly shite, there are some specifically good ones tho that get used a lot, gorge road, greenhill road, norton summit, corkscrew road

im sure everyone else can suggest some good routes

-D

most roads in adelaide are truly shite, there are some specifically good ones tho that get used a lot, gorge road, greenhill road, norton summit, corkscrew road

im sure everyone else can suggest some good routes

-D

hm. this is exciting, i've never driven interstate before, will be going to o'sullivan beach to meet up with the kitty breeder, then perhaps, do some fishing, and beachy stuff when it gets warmer (hopefully).

Then spend the night at somewhere cheap (recommend!)

And in the morning, head down to mt gambier to cheap out that blue water and that cave, and also do some fishing, and whatever that can be done there. Then head back down on the GOR on a nice weekday morning, and that shall it be. Back to work on friday.

dont leave your car at o sulleys beach, shite hole

adelaide roads, I've driven on smoother dirt roads. , like someone carpet bomb'd the place holes everywhere ?

and defect central

and make sure you have an alarm, lots of skylines stolen lately, keep valuables out of sight !!!

Aldinga beach/silver sands is nice, not far from o sulleys , drive on the beach, 8km long, good fishing, watch for sharks, dophins a plenty

they have a caravan park on the beach, not sure how much ??

or victor harbour area is nice ?

Edited by sapphiregraphics
So you'll be down here Tuesday.

I say go to the Ferrari trackday at Mallala.

edit - oh, and for the odd late-night session early in the week - Sugar on Rundle st in the city

Wait... Sugar is open on a Tuesday night? I wish I had known that a few weeks ago haha!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Not sure the US can import anything other than the C34 Stagea's, but if you can and you need to to tow, DO NOT under any circumstances get an M35 Stagea. If it is just as a family car and your country/state allows it, absolutely and definitely get an M35 (3.5L if possible as it is effectively a 350Z) over a C34.
    • Punch your VIN (nm35-xxxxxx) into Amayama.com You can see everything there quite easily.
    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
×
×
  • Create New...