Jump to content
SAU Community

Just Had My Car Dyno'd

Blizzerd

By Blizzerd,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Blizzerd Experienced

Blizzerd

Posted
Posted

So its pretty much stock S2 stagea with blitz air filter and exhaust with sbc i colour, i have a little box in the passenger footwell with SIDC box???

it has a mines ecu with :

Fuel mapping has been changed

Ignition timing adjusted

Speed limiter cut

Rev limiter raised plus(+) 300rpm

Guys at autoworx recomending i get a new fuel pump.

I want to get a new ecu as it is.

here is dyno sheet, i believe this is on mid level boost....

S50C-110111615350.jpg

Link to comment
https://www.sau.com.au/forums/topic/344518-just-had-my-car-dynod/
Share on other sites
wht510 Experienced

wht510

Posted
Posted

Nope.

It is kind of like a piggy back but is sort of like a completely new ECU. It is additional 'address space' and kind of interrupts the factory default values and is placed inside the factory ECU.

This basically allows you to have full adjustment of pretty much everything via the consult port via some cheap laptop software downloaded from the nistune website. For example, I can now change the Thermo fan set point which was usually an 'emergency thermo' for my SR20DET. I've removed the factory clutch fan and now the ECU takes care of cooling duties!

JOHNNNY Explorer

JOHNNNY

Posted
Posted

hay man that mines ecu you have the best thing to do with it is to remove it and throw it in the bin !!!!! my mate had one in his 33 and it caused all kinds of problems for him and never tuned properly , and would always lean out on a high boost setting and could never hold a smooth AFR for some unknown reason . seriously man the best thing to to is to spend the 400 bucks on a nistune daughter board installed into a STD ecu and all your problems will be solved . my s2 before i installed the nistune was pulling 235 hp on 10 psi , and 2.5 exhaust std cooler and turbo smart boost tee . now i have a 3'' exhaust , FMIC and coustom intake setup , but i havent had it tuned yet because of getting hit in the ass by a stupid ford driver and having to get it fixed but now i have it back so it should be all go after christmas , and im hoping for around 290 -320 hp at all fours with a goog tuner . cheers spinner ..

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted
How much are they normally
See if this one's still for sale - I think he wanted $400 for the ecu c/w nistune chip - you could just plug it in an get a tune.

http://www.skylinesaustralia.com/forums/Ni...fm-t340680.html

RubyRS4 Grand Master

RubyRS4

Posted
Posted
See if this one's still for sale - I think he wanted $400 for the ecu c/w nistune chip - you could just plug it in an get a tune.

http://www.skylinesaustralia.com/forums/Ni...fm-t340680.html

+1

$450 I recall for the ECU.

Thats if its still available. The thread was killed by some non-buyers tearing at it.

bubba Grand Master

bubba

Posted
Posted (edited)

The board itself is about $280, a single user license for the NIStune software is $200 I think (you don't need this, it's only if you want to be able to fiddle with stuff yourself, or ask me to do it :) ) - both purchased straight from NIStune.

Carton of beer to a competent electronics technician to install the board.

Then find your tuner of choice (I can recommend Hyperdrive and Allstar Garage) and pay by the hour for tuning. Shouldn't take too long as it's pretty much stock.

Edited by bubba

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...