Jump to content
SAU Community

Recommended Posts

all off my series 1 r33, gone to the dark side and bought a s14 lol

all still on car and can be heard or driven, untill parts sell that immobilise vehicle ofcourse!

redcliffe qld

Ph : 0426261146

have a set of tein ha height and damper adjustable coilovers - $900

cusco non sunroof half cage with the rear crossbar will also suit r32 2 door (chromoly = lightweight and sexy as) - $550

cusco front castor arms - $150

boss kit - $40

jjr rear camber arms -$100

ducktail rear wing (painted gunmetal) - $100

nismo 300km/h dash with blue backlighting -$300 ono

Tomei 2-way diff perfect - in housing -$750 just the center - $650

power fc and handcontroller(tuned with mods listed forsale underneath (341.8hp tune) - $1300

660cc sidefeed injectors in factory rail (cannot remember brand) - $450

80mm throttle body - $200

rb25 s1 splitfire coilpacks -$400

front facing plenum (leaked coolant when bought, had repaired daily drove for last year no issues at all) - $200

z32 afm with plug - $250

4 inch HKS exhaust has one hotdog muffler in middle and cannon at the back, very unique nice sound - $300

garrett t04e turbo with the dump/front pipe to suit - $600

stainless low mount exhaust manifold - $100

HID headlight low beam only - $100

3 inch stainless dump pipe to suit standard turbo(turbo to cat) - $80

hicas lock bar - $100

greddy bov with greddy adaptor to suit rb engine - $250

uras drift pinaples . used but like new - $100

Link to comment
https://www.sau.com.au/forums/topic/345170-bens-r33-part-out-sale/
Share on other sites

hey im interested in stainless low mount exhaust manifold - $100. what condition is it in??, and has it blowin weld joints before?.. much boost that went through this?. thanx

Front facing plenum (leaked coolant when bought, had repaired daily drove for last year no issues at all) - $200

do you have pics of this? brand?

  • 2 months later...


  • Similar Content

  • Latest Posts

    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
    • This looks great! Awesome to have the 5 speed with an LSD in this. The Recaro's look like SR2's or SR3's. It's a shame they've been retrimmed as they would have looked sweet in their original colours. I think I'd want my agent to be a little more up front and informative too. I've never imported but I reckon it would make me a little nervous, so the more info the better.
×
×
  • Create New...