Jump to content
SAU Community

Recommended Posts

As for sourcing the rims, once you find what you want, give Jesse Streeter an email, and I could almost gaurantee you the price he gives you will save you a couple hundred bucks.

www.jessestreeter.com

As Nathan said above, I was there yesterday and they have heaps of TE37's to check out.

I was only going to go 285/30/19 but does anyone know if the 295/30/19 will be ok on a 10.5 wheel +11?

my car has only been lowered 30mm but I am a little concerned that the tyre will rub?

Thanks

Dave

I run 285/30 on my 10.5' and they're slightly stretched.

They could easily take a 295, or even a 305, but what is now a very slight rub might turn into a more substantial one.

My car is lowered.

~$400 saving on XD9's if i went through streeter....

that's on a 2k set of rims, so nearly 25%

paying for my cr kais from him today. 1135 w/out shipping charge should work out bout 15-1600 dollars instead of 1800-1900 as quoted by work wheels au without delivery

  • 2 weeks later...

Just put a deposit down for a set of Te37 sl 19x10.5 +22 offset. Should pick em up around the 14th of January. I most likely gonna wrap them with 295/30 Yokohama Neova AD08. Will just see how good fitment is :)

Keen to see how this turns out.

I've got a set of advan TC2s in 18x10.5 that I need tyres for.

I'm thinking if I can get away with 285/30 than I will, they're going to be track rims and more rubber on the ground is always a good thing.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If you take the top half of the intake off you can unbolt the flap off the shaft and leave the shaft in there blocking the hole. Then you can remove the little vacuum canister off from under the manifold and get a spare vacuum line to run to the ECU. I can take some photos of it later. Probably best to get the vacuum source to the ECU sorted first though. Mine all worked mint with the base map from the GTT an I've pretty much let the closed loop sort the fueling and took 1 degree out of the whole timing map.
    • This IS something you also have to configure in Haltech (or at least I did in the past when going from onboard-to-ECU map sensor and an external MAP sensor in haltech land).
    • I'm hoping it's something as simple as the ECU is looking for an external MAP sensor, but he is trying to use the onboard MAP sensor.
    • You won't need to do that if your happy to learn to tune it yourself. You 100% do not need to do that. It is not part of the learning process. It's not like driving on track and 'finding the limit by stepping over the limit'. You should not ever accidently blow up an engine and you should have setup the ECU's engine protection to save you from yourself while you are learning anyway. Plenty of us have tuned their own cars, myself included. We still come here for advice/guidance/new ideas etc.  What have you been doing so far to learn how to tune?
    • Put the ECU's MAP line in your mouth. Blow as hard as you can. You should be able to see about 10 kPa, maybe 15 kPa positive pressure. Suck on it. You should be able to generate a decent vacuum to about the same level also. Note that this is only ~2 psi either way. If the MAP is reading -5 psi all the time, ignition on, engine running or not, driving around or not, then it is severely f**ked. Also, you SHOULD NOT BE DRIVING IT WITHOUT A LOAD REFERENCE. You will break the engine. Badly.
×
×
  • Create New...