Jump to content
SAU Community

Recommended Posts

if you can find 3 local tuners who can tune, recommend and use it and can offer a reasonable price for install and tune go for it. there is no point picking an ECU that no one can tune, so best you check before anything.

my advice do like everyone else

powerfc

nistune

vipec

should be lots of local tuners, good options, good pricing as you can choose the tuner etc

fkn megasquirts is all ill say.

Ive added them to my no touch list as all the owner built ones seem to come in with a plethora of issues.....

^^

there are much better ecu"s out there, i had a mate try 1 in his datto w/CA18..........it was a nightmare to setup as he used a ford ignition w/crank pick up and there was no tech support as they are based in england (so you have to call them at crazy hours).

stick to what has been tried & tested - Vipec/Link, Power FC, Nistune. at least all these are plug & play ecu's. there are plenty of people out there that have a lot of experiance with them.

Megasquirt is a good ecu but you have to have someone that knows what he's doing to work on it. A friend of mine got one in his BMW that made 390+ rwhp and 390+ torque. Car is insane, but.... i wouldnt put it in my skyline, too much hassle to make it work on a RB motor.

for what it's worth any ECU can make power, any ECU can make 100rwkw, 200rwkw, 800rwkw, 1200rwkw

how the ECU is tuned, the car, the usage requirement, it's usability, how it installs, features, support when things go wrong, price and availability of tuners is what is the deciding factor when choosing an ECU

so forget how much power a guy can make using an ECU

megasquirt is a owner made ecu for tinkering around and just having a mess around, great if you want to add loads of custom features yourself or are making an old carby car ecu but if you are not doing it yourself all you are doing is making it impossible for the tuner for no gain, generally they aren't a very good ECU and I would say its a large downgrade over a nistune.

Nistune is what I'd recommend for a near stock car, cheap, looks standard, no new wiring, simple to tune and large amount of tuners available.

^^ exactly they are generally fine with owners who have a clue about wiring and electronic principles, in fact give good results on the cheap as the owner can get most parts (triggers sensors etc from wrecking yards)but the the problem is most people with no clue see the price then buy it. try install it... fail then drop it to a workshop to sort out.... which is a night mare for us as often it is cheaper and easy to rip the lot out stick a std loom back in nistune it...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...