Jump to content
SAU Community

Recommended Posts

Redirect the exhaust flow to pass through the charcoal canister first? Though you would probably introduce some backpressure via 10mm hoses to the canister itself and negate the straight pipe.

Redirect the exhaust flow to pass through the charcoal canister first? Though you would probably introduce some backpressure via 10mm hoses to the canister itself and negate the straight pipe.

And then into the passenger cabin :thumbsup:

he wants to tune out the smell from a decat exhaust.

the only way to do that is by changing the mixtures, which would alter the motors tune etc. not advisable.

if you want to run decat you will need to wear the risk of $15,000. pretty much end of story.

otherwise you are welcome to lose 3kw and run a decent cat for the price of an extra $400

FYI $15,000 > $400

he wants to tune out the smell from a decat exhaust.

the only way to do that is by changing the mixtures, which would alter the motors tune etc. not advisable.

if you want to run decat you will need to wear the risk of $15,000. pretty much end of story.

otherwise you are welcome to lose 3kw and run a decent cat for the price of an extra $400

FYI $15,000 > $400

This "fine" has gone from "$10000", to "$750" (I believe Stao/Hypergear was the one to cop this fine) to now $15000.

I wouldn't be surprised if it were nothing more than a defect notice at this rate.

Also, OP - just run it SO LEAN that the engine won't even fire up. Then you'll never have any exhaust gas passing through the system, and therefore no smell!

This "fine" has gone from "$10000", to "$750" (I believe Stao/Hypergear was the one to cop this fine) to now $15000.

I wouldn't be surprised if it were nothing more than a defect notice at this rate.

I have been of the understanding that it was $15,000 for the last decade, unless times have changed.

It will be a circumstantial penalty, depending on your situation. Yet do you really want to take the risk? And do you really want to leave noobs with the impression they may just get a defect notice?

Obviously it is the owners decision, yet a well known POOR one at that. A few KW really isnt worth the hassle.

A screamer on the other hand :P

Can you still get a fine if your car is Unregestered but driving on a permit? My exhaust is straight through no cat not muffler... just say if i went to a workshop and a cop pulls me over but im on a permit is that ok?

it will be tough to do but leaning it out at idle and cruise etc should reduce the emissions a bit and thus reduce the smell too but basically without a cat you are going to be up against it to change things much just by altering the tune. unless it's rich as all hell at the moment in which case a tune up with a leaner AFR across the board would certainly help. but to be honest if it's a problem then you are better off spending the money on a good cat.

he wants to tune out the smell from a decat exhaust.

the only way to do that is by changing the mixtures, which would alter the motors tune etc. not advisable.

A cat turns carbon monoxide and unburnt fuel to carbon dioxide and water.

It hasn't really got anything to do with the tune unless his is tuned very rich. He can lean the motor out but it will still have the smell of running no cat since the smell is carbon monoxide.

To answer the OP's question in a serious manner, no you can not. Whatever you have read about "EVO's" doing it, you have miss understood.

A cat turns carbon monoxide and unburnt fuel to carbon dioxide and water.

It hasn't really got anything to do with the tune unless his is tuned very rich. He can lean the motor out but it will still have the smell of running no cat since the smell is carbon monoxide.

To answer the OP's question in a serious manner, no you can not. Whatever you have read about "EVO's" doing it, you have miss understood.

it will be tough to do but leaning it out at idle and cruise etc should reduce the emissions a bit and thus reduce the smell too but basically without a cat you are going to be up against it to change things much just by altering the tune. unless it's rich as all hell at the moment in which case a tune up with a leaner AFR across the board would certainly help. but to be honest if it's a problem then you are better off spending the money on a good cat.

This.

Agreed you cannot tune out the issue, but you can centainly try to change the mixture so the smell is not so evident.

Either way I think it is a silly idea, just put a damn cat on or wear the risk.

Im not sure about state to state but as a general the car is out of the cops 'jurisdiction' when being driven on a permit unless it is- 1: dangerous to drive, 2: being driven dangerously.

so based on this the decat is fine on a permit...

Can you still get a fine if your car is Unregestered but driving on a permit? My exhaust is straight through no cat not muffler... just say if i went to a workshop and a cop pulls me over but im on a permit is that ok?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...