Jump to content
SAU Community

Recommended Posts

Yeah I looked up power chip and found that they don't have a rb25de chip I would say that the Nistune would be the best way to go though I can't find any forms, that have information on them. only thing I can find is a video of an r33 on a dyno with a Nistune with BIG power gains.

Yeah I looked up power chip and found that they don't have a rb25de chip I would say that the Nistune would be the best way to go though I can't find any forms, that have information on them. only thing I can find is a video of an r33 on a dyno with a Nistune with BIG power gains.

http://www.nistune.com/

tried their website :geek:

Yeah I looked it up Abit more and found that I could get the nistune done off envy inports in sydney for $1100 so that sounds great and that would give me 20 more kws at the wheels and get cams done for about $1200 but I think that's abait to much of a power gain for a p plater

I have been told many many times Nistune does not work on the RB25DE ECU (R34 GT)

nfi about R33 or 32..

You have to buy an ecu out of a z32 and modify it a bit, put the nistune in and then it will work with the rb25's.

Another option is to use an r32 ecu with the nistune, but then you lose the VCT.

Might as well buy a whole new ecu?

if I have to buy a another ecu then buy the Nistune. I don't have that much money. lol I am saying this because they can just upload the Nistune software on it right?

no you can't simply load the nistune software (or any software for that matter) onto any stock skyline ecu. they require a daughterboard installed into the ecu, but not all of the skyline ecus are compatiable. most places should be able to get you a z32 ecu, install the board and then tune if for around $1000 to $1200. z32 ecu's can be had for pretty cheap these days (under $200). to put this into perspective, most stand alone aftermarket ecus cost quite a bit more than that for just the ecu without any tuning done (and the lower end aftermarket ecus such as the pfc won't give you any real advantages of difference in performance over the nistune).

also for a NA i wouldn't expect a 20kw gain in power from a tune. i'd expect more like 10kw. 20kw is more what you'd gain from a tune on a turbo skyline.

that 20kw was probably a bit of a one off. you will find that the average power gain they see is probably less than that. also there are some tuners out there who will do a tune, then if the power gain isn't that much they then alter a few settings on the dyno to bump up the power figures (and it's not always the ones who are known to be dodgy, plenty of the 'reputable' ones have done it too). not saying that the place you are talking about would do that, just simply saying that expecting 20kw from a tune is a bit much for an NA unless you were putting in a set of cams too, or the stock ecu was throwing a fault code and they fixed that at the same time.

as for 20kw damaging the engine, that depends on the tune. a 20kw gain won't damage the motor simply from the extra power, however if they do a safe tune and it only makes 5 or 10kw more and they want to make it a bit better then they may start to add a bit more timing into it or lean it out a bit more and start to make it not so safe. this then reduces the margin of error that the engine has if something happens such as the fuel pump starts to die or an injector gets a bit dirty. this is part of the reason why power can be gained over a stock ecu. they are tuned to be extremely safe to give a large margin of error.

  • Like 1

U seem to have a good idea on this. What do u think I should do I have an exhaust pod cai but it just doesnt put out enough for a skyline u know I just want enough power in case a xr6 or a sv6 comes next to me on a race track;). That's all I want 0 to 100 in 7seconds. :)

you will have to face the fact that a NA skyline simply isn't that fast. if you go up against a falcon or commodore with similar mods to you you will lose. i've said this many times on here, but i will say it again (so sorry to those who are sick of hearing it). i had a 3.5L v6 manual magna. with just a cat back exhaust it ran 14.8 at willowbank. it was just the base model executive. there are plenty of vrx versions in the 14.4 to 14.6 bracket with minimal mods (full exhaust).

you will have to face the fact that a NA skyline simply isn't that fast. if you go up against a falcon or commodore with similar mods to you you will lose. i've said this many times on here, but i will say it again (so sorry to those who are sick of hearing it). i had a 3.5L v6 manual magna. with just a cat back exhaust it ran 14.8 at willowbank. it was just the base model executive. there are plenty of vrx versions in the 14.4 to 14.6 bracket with minimal mods (full exhaust).

I wont say anything :nyaanyaa:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
    • Is this a brand new LSD? if so, have you followed any break/bed in procedure for it? Usually involves heaps of figure 8 patterns, a fluid flush.
×
×
  • Create New...