Jump to content
SAU Community

Recommended Posts

Hey everyone,

last time i was at eastern creek i was told that the helmet i have is longer up to aussie standard and was told before i go back next time ill need a new one

now what i wana know is where in the wollongong/ sydney area is the best/ cheapest place to get motor sport helmets from?

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/
Share on other sites

http://bikegearwarehouse8-px.rtrk.com.au/mx-gear/Mens_Motorcross_Helmets

or goto your local bike shop...they always have specials

eg today i got my carbon/kevlar MX helmet for 150bucks

basic open face helmets can be had for 80bucks but they are heavy and..... well shit to be honest

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5624891
Share on other sites

Hey everyone,

last time i was at eastern creek i was told that the helmet i have is longer up to aussie standard and was told before i go back next time ill need a new one

now what i wana know is where in the wollongong/ sydney area is the best/ cheapest place to get motor sport helmets from?

Does it have as AS sticker on it? What brand/model and how old?

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5624919
Share on other sites

Does it have as AS sticker on it? What brand/model and how old?

+1, what standard is it that was knocked back?

CAMS helmet requirements are here: http://www.camsmanua...dule_G_Q111.pdf

importantly, it includes the following:

4.8 Moratoriums

(a) There is a moratorium on the implementation of any changes to apparel requirements, save for any identified and pressing safety related requirements which may arise or become evident, for non-international events, until 31 December 2012.

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5625306
Share on other sites

It's been like that for ages and It's all pretty clear on their website:

Helmet Standards approved for Race for Real Off-Street Meetings

Drivers Drivers of vehicles slower than 10.99-seconds (1/4 mile) are permitted to use any helmet (full-face or open- face) meeting one of the following Standards:

• SNELL SA2000, SA2005, SFI 31.2A (USA)

• SNELL M2000, M2005, SFI 41.2A (USA)

• BS 6658-1985

• AS/NZS 1698:2006 or AS/NZS 1698.

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5625690
Share on other sites

yeh i never knew that when i went up last time coz before that i had never had a problem and helmet is still in basically new condition.

but anyway im going to make a trip up to the place in auburn in the next week or so

Link to comment
https://www.sau.com.au/forums/topic/350304-helmets/#findComment-5625943
Share on other sites

  • 3 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Perhaps the answer is... more jacks!* *proper jacks must be used.  
    • I NEVER think about using a scissor jack unless there is absolutely no other alternative. f**king things are dangerous, annoying and stupid.
    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
×
×
  • Create New...