Jump to content
SAU Community

Recommended Posts

Hi all

Its nice to see your entries coming through for our HH hills rounds.

A few more would be nice ... at 22 entries you people get lots of runs ... but i lose a few 1000' $nyaanyaa.gif

Haunted hills is a great spectator/photographers track as well, and the food isnt bad.

And yes that rotary is A03 for our championship ... if you come first against all those Bl00dy V8 holdens I will give you a trophy.

  • Replies 92
  • Created
  • Last Reply

Top Posters In This Topic

i dont like my chances being that its my first track day but i will try!

that is only if my membership comes through before the entry cut off!

i take it you cant enter and pay at the gate?

i dont like my chances being that its my first track day but i will try!

that is only if my membership comes through before the entry cut off!

i take it you cant enter and pay at the gate?

Nah sorrry cash on the fridge ..

ie Formal entry and pay before go

sorry but for several reasons we dont accept entries on day.

However if your membership to SAU is in progress I will accept some form of semi proof on that.(on the day)

So enter

I'd like to announce the 2011 DECA dates have been booked. Martin has updated above with the info.

Bring on another great year!!!

hey guys, just wondering, is there a number i can contact you on cause i'm useless on computers and email, to join?

i was hoping to have a look at hh and get info, but my gf fractured her ankle and couldn't go.

hoping to be a member by next meeting and give one of my cars a squeeze.

also, i run full slicks when i practise in my gtr, is unlimited, totally unlimited? thanks Simon.0414347750

  • 2 weeks later...

Only one weekend until Calder, get your entries in and your cars prep'd people!

pirate.gif

5th of March.

What he said... Bob Janepirate.gif is getting all my money, please come along so i dont need to beg on streets thanks.gif

And I do need some Nissans to show up those silly drifting Holdens we had at HH.domokun.gif

Entries close Tomorrow week

What he said... Bob Janepirate.gif is getting all my money, please come along so i dont need to beg on streets thanks.gif

And I do need some Nissans to show up those silly drifting Holdens we had at HH.domokun.gif

Entries close Tomorrow week

can you give me some more info on how to join up. i'm better on the phone at the moment 0414347750, just text and i'll call you back.

i have a nissan and i'm trying to make the calder event

thanks simon.

can you give me some more info on how to join up. i'm better on the phone at the moment 0414347750, just text and i'll call you back.

i have a nissan and i'm trying to make the calder event

thanks simon.

all info on how to join can be found :

HERE

http://www.skylinesaustralia.com/forums/topic/288195-become-a-member-of-sau-vic/

  • 3 weeks later...

That is the objective this year.

But after first round was waiting on people for classes up till a couple days b4 calder.

So thought I would give the webmaster a break and only send it once.

results up

http://www.sauvic.com.au/motorsport_championship

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
    • Hi all,I already introduced myself in the Victoria section, but only saw this section now lol XD New to forums and new to skylines. Hoping to buy my new skyline within October
×
×
  • Create New...