Jump to content
SAU Community

Show and Shine Preparation - Part 1 (Spot the GTR)


Recommended Posts

Thought I would throw a few piccys up of the way my car looks right at this moment. Call it a shell of its former self :D

This is a snippit of the work thats currently underway in preparation for the Show and Shine event.

This used to be my silver R33 GTR

dsc00386.jpg

dsc00388.jpg

dsc00395.jpg

dsc00392.jpg

dsc00399.jpg

dsc00400.jpg

dsc00401.jpg

dsc00408.jpg

dsc00404.jpg

dsc00409.jpg

And here is the mad scientist at work. I stood and watched this guy for a bit - im looking forward to the end result!

...im just looking forward to seeing it all put back together with the end result being a GTR.

I'll give ya fifty dorah for each front guard :wassup:

Lemme guess, fluro pink ?

RedlineGTR: The car is receiving some serious panel preparation ready for a custom respray with best quality finish possible.

No fluro colours - but rather an extremely high gloss metallic titanium mix.

Project is around 3 weeks worth so a bit to go yet :D

Hmmmm we better fix that best interior / best exterior thing hey.

Nice one Blitz - I wish I could afford to do mine too ATM - But will have to wait until more funds are available.

I think I'll be going with my standard colour - but I want to put 2 nice thick racing stripes down the length of the car - What do ya reckon ??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
    • Hi All, putting the engine back together and everything is perfect except have this plug left over.. any ideas what it is for and where it goes? Is on cold side under the intake plenum *note not a stock plug, as everything has been modified Cheers
×
×
  • Create New...