Jump to content
SAU Community

Recommended Posts

  • Replies 115
  • Created
  • Last Reply

Top Posters In This Topic

you probably were looking at the wrong time Nismoid - mine shows up as 98 when the needle on my speedo is 100. I have done this test at least a dozen times in the last year and it always says 98 if I am on 100.

Maybe your cars' speed sensor is stuffed...or maybe your looking at the wrong lane reading...

:shrugs:

It works for me.

yeah fair enough,

when you are in heaps of traffic its sometimes hard to workout which one is yours!

also last time i did mine the car next to me was sitting on the same speed but his registered at 101 or something...oh well.

As long as your speedo is under and not over then you are better off!

I'd rather my actual speed be like 95 when i am sitting on 100 than say 105, cause you could cop a fine, so to speak :)

it's outta whack.

TRUST ME!

Andrew and i, then Nathan and i have been through it... and it was FAR from reading what the speedo was.

That meter is on drugs

Dude, I used to drive past that thing 3 times a week on my way to work. It is accurate!! It reads 100 when my speedo is dead on 100...

Nope! it dont!

I've been in two cars little traffic (read:no cars near us) and it was reading weird!

Maybe a bunny rabbit tripped it off or something ?

Meh. I dont care. Speed Camera's aint accurate... speed detectors wont be either

Danny, is this happen to be the one near the St Vincent Hosp?

Funny sign with a :stupid: when u're under and a :starwars: when you're over he he he

I had a sign tell me off for doing 51 today in a 50 zone and then compliment me for slowing down!! Stupid sign!

This one is in a back street in Dandy nth/Noble park and displays text like TOO FAST! and WELL DONE!

I want to change the program to SLOW DOWN YOU IRRISPONSIBLE ****NUT and TOO SLOW YOU DOUCHE!

The speed meter thingo was 2 km/h off what my speedo said when i went through on the cruise. I checked my speedo with a handheld gps a few weeks ago and it was always correct give or take 1km/h. So i think my speedo is pretty accurate and that the speed measure thing is pretty accurate too.

I think the government should put in a bit of the money theyre making from all these fines into building a few more of these speed measurers, it would be great to be confident that when youre doing 103km/h that ur not going to be booked.

Guest
This topic is now closed to further replies.



  • Latest Posts

    • I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
    • Thanks for the info. The only "Issue" I've had with the shifter is I always found the throw between 4th and 6th gear too close. I'm always worried to shift into 4th accidently and sending my motor to the moon. Adam LZ recently came out with a video and stated Serialnine revised their shifters to correct this and will change all the revised parts for 150$. Strangely enough, I contacted Serialnine right after and they denied it and said it's bullshit. I found that strange as he's a distributer. I'll keep this forum post updated on that saga.
    • Yep that is correct. It allows you to adjust the short throw range from what I can tell
    • Car has been running great, I've put about 300km's of break in time on it. First thing that stands out with properly sealing rings is no more noticeable crankcase smell coming out of my catch can. This may seem insignificant, but the constant smell while driving around was infuriating. It's also nice to see my oil level remain stable. Two new issues have developed that I only noticed this weekend though. There's a very noticeable driveline vibration past 100kmh. I only noticed it now as I've been babying it under 100kmh in the backroads. This comes as no surprise as I'm running a one-piece shaft, and I paid zero attention to my driveshaft angle when I put everything back in. I also have a fair bit of voltage drop on hot starts. The starter audibly is forcing. No issues on cold start though. I must not have removed all the paint under my main block ground during assembly. I'll try and take care of both those issues this week once the kids are asleep.  I also received all the parts I was missing for my direct port setup. I will hopefully have pictures of that up soon. I'm hoping to get back on the dyno the week of June 30th as I'll be on vacation. I'm confident I should be able to make north of 500rwkw on pump gas and WMI. I'll go back again later this summer with E98, but I want to confirm my ethanol content sensor is working properly first. I've never seen it read anything but 11%. This makes sense for our 10% ethanol content pump gas here, but I would expect the occasional movement between fill ups. 
    • 75% complete. Will now need to get a new axle with 5x114.3 hubs and then figure out how to customize some mudguards for it once the wheels are on.
×
×
  • Create New...