Jump to content
SAU Community

Recommended Posts

hey people, done a quick search but couldnt really find anything,

is anyone using the cooling pro r33 ally radiator in there s1??

i know i will have to use an auto cooler thats not a drama but really want peoples opinion on fitment, size and if the shroud actually fits!

thanks people!!

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/
Share on other sites

You need a AUTO specific rad with the bottom tank setup for auto trans fluid. That bottom tank isnt their to "cool" the fluid its their to get it up to temp and keep it at as much of a consistent temp as possible..

I have heard that before. So why have a tranny cooler??? >_<

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5651040
Share on other sites

I have heard that before. So why have a tranny cooler??? pinch.gif

Not trying to sound smart, but there seems to be a bit of confusion surrounding trans coolers and their use; hopefully this helps.

The thing in the bottom tank is a heat EXCHANGER; not specifically a cooler or heater.

If the water is hotter than the trans fluid; heat will be transferred to the fluid, if the fluid is hotter than the water; heat will be transferred to the water.

Under duress, the trans transfers a decent amount heat into the trans fluid, it can easily go over 100 deg in the right conditions.

The heat exchanger in the radiator is usually nothing more than a simple copper or aluminium tank, no fins for extra surface area. They are not particularly efficient.

So in extreme conditions with high water temp, using a dedicated trans cooler is much more effective at stripping that heat out of the fluid, making life easier for the gearbox.

Also, ambient temp is always going to be lower than the temp of the water in the cooling system.

A side benefit is reduced load on the cooling system.

Running the fluid throught the radiator mounted exchanger, in addition to an external cooler just ensures the trans fluid will be around the same temp as the radiator water, not ambient temp in cold conditions; as Pipster & Kidafa have said.

Edited by Daleo
Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5651186
Share on other sites

i dont understand either, the auto-trans specialists up the road from my work say built in radiator trans coolers are rubbish. and then why do people fit large external trans coolers for "towing/extreme condition/high perfomance applications" ? also read an article in a 4X4 mag that said the higher your auto fluid temps the shorter your auto trans life and it had a graph with "auto fluid temp" over 'hours of life".

all autos will be sluggish when cold regardless of 'heated' or external cooler. My x-trail i just sold (my07) had a built in cooler and i fitted an external cooler and it drove the same, had long drawn out gear changes for the first 5 mins of driving til the trans fluid got up to temp, the external cooler didnt take any longer or shorter to heat up than the built in one.

personally i would run the cooling pro manual stagea 3 core radiator, a moderate size external tranny cooler and a top quality trans fluid.

also as chuckie mentioned, use the search function and there is a billion radiator and tranny cooler threads

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5651192
Share on other sites

if i did it again, i'd get one of the asi radiators from ebay

same quality as cooling pro (ok for china) but about $100 cheaper

oh, and i read about the auto heat exchanger, you only need it in cool temps or your fluid will not warm up if you have an external cooler

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5651263
Share on other sites

yeh like if you live -20 degree conditions in the middle of the day you would need it, i believe now some german cars have electric elements in the engine oil sump to heat the oil so its easier to crank when cold?

In some sub arctic countries, rather than heat a garage, they do exactly this, just need to remember to plug your car into the power point before going to bed.

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5652579
Share on other sites

In some sub arctic countries, rather than heat a garage, they do exactly this, just need to remember to plug your car into the power point before going to bed.

my aunt in canada has had that for years

also means that the heater blows hot air as soon as it turns on

Link to comment
https://www.sau.com.au/forums/topic/352379-radiator/#findComment-5652862
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...