Jump to content
SAU Community

Recommended Posts

  • Replies 81
  • Created
  • Last Reply

Top Posters In This Topic

no real information to update...

your welcome Charles

and Carlo they are top feed high imp, Heslo has just bought a set so somehow they must suit RB26dett's

as soon as the supplier puts together our price's i will update i do have small update he told me today he also sells fuel pumps and gave me retail prices on them, unfortunately i left the paper work at work but ill go from memory

Bosch 044 $215

Bosch 040 $187

Walbro Int. $136

Walbro Ext. a little dearer than $136 but cant quiet remember he will supply me with new group buy prices on the fuel pumps also

all items pumps and injectors come with a full 12 months manufacturer's warranty and 100% authentic no Chinese copies

probably not PM sent i may extend this GB as i don't want to rush information but i wanted to get it started

and i will make a thread in the GB section and put a link for everyone to go register on

Hmm i found this bloke on EBAY, looks like he also sells Siemens 890cc Top feed Low Impedance EV1 Injectors for $79 each.

Following Stats:

Static Flow Rate: 83.2 lb/hr = 10.87g/s = 888 cc/min (+-/ 4%)

Dynamic Flow Rate 2.5ms PW @ 100Hz: 19.5mg/pulse (+/-4%)

Coil Resistance: 2.35 Ohms / Low Impedance / Low-Z (Peak/Hold driver circuit required)

Spray Pattern: Pencil

Connector: Minitimer (Bosch EV1)

Only downside i could see here is you would need a 14MM fuel rail.

Edited by ZED X

hahahah did you note the seller, did you note in post #1 where i said parts are coming from :D

and RB20,25 want high impedance GTR use low impedance and Heslo didn't get back to my txt

and the 80lb Siemens injectors on his webshop are dearer than he quoted us already :D :D

Steve - what size RB25 injectors can you get? Currently using S15 450'cc and dont want to go up too big, ie 550's, 600's etc

Whats available?

cheers mate..... if i upgrade the injectors I'll definitely (finally) bolt on the exh.manifold and perhaps look at a greddy-copy intake plennum.

one last tune perhaps :)

this i might be interested in steve.

aye - is it wideband, and compatible with nistune/pfc?

These innovate units work with nistune for sure, and look quite decent

http://www.innovatemotorsports.com/products/db.php'>http://www.innovatemotorsports.com/products/db.php

http://www.innovatemotorsports.com/products/lc1.php'>http://www.innovatemotorsports.com/products/lc1.php

Thats what I'm semi keen on... does that one talk to nistune ?

-D

6. What Wideband support is there?

Currently NIStune supports the following Wide Band units:

TechEdge 1.5 and 2.0

http://www.techedge.com.au

Innovate LM1 and LC1

http://www.innovatemotorsports.com

AEM UEGO

http://www.aempower.com

Zeitronix

http://www.zeitronix.com

PLX Devices (R Series)

http://www.plxdevices.com

MOTEC PLM

http://www.motec.com.au/plm/plmoverview

Just Another Wideband

http://www.14point7.com

VEMS Wideband

http://www.vems.co.uk

DLP Design A/D Converter

http://www.dlpdesign.com/usb/io8.shtml

These units connect to your laptop via the serial port (or USB port when using serial-USB adaptor). These units output data to allow NIStune to monitor your Air Fuel Ratios from their sensor, and some produce auxillary inputs for connecting other sensors which can display and log inside NIStune.

NIStune provides several internal utilities to make the most of your Wide Band

- Dyno Mode AFR graphing against RPM

- Real time AFR and auxillary map display (minimum AFR, maximum AFR and current AFR against the fuel map)

- Logging and playback of AFR

yes the unit is wideband

looking into if its a nistune compat but i dont see why as it has its own box to read the O2 sensors that comes with it

oh :( the whole kit the guage i posted and 02 bit is $504

that below is the rest of the kit

http://www.dynojetwb2.com/images/products/wb2_kit_1.jpg

Brendan if you only want 500cc i can get the 52lb/h injector there around 535cc

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...