Jump to content
SAU Community

Aluminum Flywheel's

MJTru
 Share

Recommended Posts

MJTru Mentor

MJTru

Posted
Posted

Hi Mate

I just got a clutch master twin plate 850 series twin plate clutch for my rb build, but after reading the manual i noticed that i need a torque plate when using a aluminum flywheel, because the bolts can cut into the flywheel when i'm tighten them or worst come loose. Does anyone know why the kit doesnt come with this plate??? do i need it still????

Were can i get one from.???

thanks in avance

Link to comment
https://www.sau.com.au/forums/topic/352650-aluminum-flywheels/
Share on other sites
MJTru Mentor

MJTru

Posted
  • Author
Posted

Your kidding right?

no i'm not, we dont have those over here. I googled it and saw an ugly car that comes with a inline 6. Is that it.???????lol

I was thinking, can i use some steel washers on the bolts insted of the whole ring.??? The washers should protect the aluminum flywheel when i start tightening it.

I acn also test fit the flywheel to the crank before i start to build the motor to make shore that the bolts of just right, length and all. what do you guys think????

MJTru Mentor

MJTru

Posted
  • Author
Posted

ok i contacted clutch master today, and they said that i can go ahead and install it with out a torque plate, with i dont agree with, they also said that they are in the process of making a torque plate for this application.

I was wondering if the washer idea would work. 2-3 weeks for the torque to be made a mail to me. Well i have made up my mind to wait for it I will not install it with out a torque plate. If i didn't need it they wouldn't be making it. thats what i'm thinking.

StealthX Veteran

StealthX

Posted
Posted

thats a good idea mate, but whats a vl???????

Your kidding right?

no i'm not, we dont have those over here. I googled it and saw an ugly car that comes with a inline 6. Is that it.???????lol

haha that's it!

hahahaha, sig'd!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...