Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...

That dash wouldn't be hard to replicate poit. I personally wouldn't give up my factory dash for that, but that's me. To make that in 1-1.6 mm ally sheet would be fairly easy, weekend job tops. Looks to be just satin black, few hole saw bits to match ur gauge sizes etc. looks NASCAR spec

Edited by Mr. Untouchable

yeah I think I should just tidy up my stock dash and leave it, take the heater core and AC out too, seeing as they're not hooked up...

I need to make some door cards more than anything!

Edited by zoidbergmerc
  • 3 weeks later...

I've been fooling around with the 33 and took some pics to share.

So I thought I had a pretty major problem when at symmons plains I was getting some SERIOUSLY bad vibe through the wheel\car when going faster than 90kph. I was like the f**k my car is going to fall apart.

I was pretty convinced that something was seriously a miss with the passenger side front suspension\bearings, something was not right. I pulled it all down and low to behold, it was all brand new, it wasn't till I was putting the wheel back on that I discovered the massive flat spot on the tyre -_- FAIL

20120720_182839.jpg

Then I painted and fitted my new wheels, they're Rays SS7 18x9.5 +38 but to get them to fit I had to install a 15mm bolt on spacer as they fouled on the upper wishbone(?) when on full lock now it clears by about 1mm. They were gold but now they're Matte black, and I'm thinking of painting the lip red to match my lensos and break it up a little. The tyres are Dunlop D03Gs in a medium Compound, 245\40\18 for the front and 265\35\18 on the back.

20120722_123612.jpg

20120722_123703.jpg

20120722_123730.jpg

20120722_123651.jpg

I'm pretty sad about my Drift Teks getting so f**ked up after my little spill at Symmons :( Those rocks hurt!!

20120722_121529.jpg

I also put in a passenger seat for the Charity Rides day in a few weeks :)

20120722_131358.jpg

I also fitted some new brake pads, Hawk DTC-60 should pull the while whale up nicely :)

Edited by zoidbergmerc

Hey Pete if you didn't already know its really easy to add a stripe to the wheels. You can either buy some red pin stripe or cut a pice out of vynal. It can just be a strait pice. As you put it on the wheel it will flex as such and turn a strait line into a curved line. So no need to paint it or cut out round stripes. I have done this neumerous times to wheels on a race car I used to look after.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
    • Agreed, and in particular the earth strap that should go from the subframe to the chassis but it often broken or left off. There is a section in the R32 workshop manual you can follow for troubleshooting if you don't see anything suspicious, and depending where you are (there is no location on your user profile) you should be able to get your hands on a second hand replacement unit still if needed
    • Yeah they mention as a R34 for 2.5 Turbo...but then again thos "small" were also for R34 by that different site. But i look into it and that 310mm EBC is for R34 GTT. And by those you linked the specs are the same 🙂    EDIT: I found these on one site here: DBA 4000 series T3 DBA42304S They are 310mm...and it says are for R34GTT...are there good? EDIT2: ok they have pads too.  What "color" should i get for street use? I dont want/need some noisy ones...(and if they are not that dusty that is good too)
×
×
  • Create New...