Jump to content
SAU Community

Recommended Posts

As the title says, my fuel gauge dropped to empty after 7mins of driving this morning.

The only thing I did was disconnect the battery, remove the washer bottle and drill a

hole under the battery tray last evening to allow fitting of intercooler pipes.

Someone please tell me whats with the fuel gauge playing up??? What should I do??

thanks

lol I get through heaps of fuel in 7 minutes.....but that is the race car at full throttle :P

it is almost certainly the fuel sender. they are a dodgy little plastic float with a metal arm that contacts on a little metal scale. if the arm is bent/crooked/mount broken it will not read right.

it is very easy to break if you move it (changing fuel pump in particular), but can even break on it's own.

just replace it....and have a good look at the new one and make sure it is good

thanks for the replies guys, after doin a lot of net searching myself I'm now certain its that bloody fuel sender unit pn top of the tank - the dodgy white plastic tube/cap with connnections. Just before I rush off to buy a new unit, I'm goin to take off and put back the battery terminals again and see whats the deal.

Starting the car again the gauge goes up to a quarter tank, then back to empty, then back up a bit while driving...then I switch off the engine and hey presto, it goes to the correct reading - about 3/4 tank. Switch off the engine and on again and it goes to 3/4 tank.

Now where in Sydney can I find a good cheap fuel sender??? Will one from the wreckers do or can't guarantee if that will work???

cheers n :thanks:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...