Jump to content
SAU Community

Recommended Posts

FS

2x R32 GTR Stock AFM's - Condition Good - $200

4x 225mm toyo t1r's, camber wear, only really usable for thrashing on the track - $50 for all 4

Front + Rear Tein Type NR Shocks - Condition Good - $500

PM me if interested

-D

hey all i have a onevia and i want to put the silvia front end back on, im not a fan of the 180 front end on the car

the pannels are in good nick, painted in white. bonnet has bonnet pins in it, can repair the holes if you dont want pins or you can have the pins for free

front guards are unflaired

would prefer to swap with s13 or s14 s2

located in SA

a pic of the front end

11042010843.jpg

R32 GTR and GTST

- 2 Air Con Compressor $40 each

- Air Con Bracket $10

- Powersteering Reservoir $30

- Glove Box $20

- Wash Bottle $10

- Foot Rest Peddle $10

- Surrounds Underneath Cluster $10

- Climate Control (Small crack on face & demister button is the car image) $20

- Plastic Container for underneath dash with 2 hooks $10

- Interior pieces to cover wires $10

- Dash Surround including gear boot, money holder and cigy..no cracks $50

- Blitz Nur Spec Exhaust Catback $250

- Air Con Condensor $50

- 2 Ignition Barrels with key $20 each

R32 GTST

- Castor Arms $20

- M-spec Blue Dash Cluster 122,322 $50

- S2 Rear Seats Good condition $50

- Rb20 Short SHORT shift kit $50

- R32 Shocks with Lowered Kings Springs $200

R32 GTR or GTS4

- Powersteering Pump $30

- Rb26 Engine Cover $50

- Centre Consol $20

- Attesa system for 4WD $200

- Boost and Clutch Master $50

- TEIN COILOVERS NEAR NEW STRAIGHT FROM JAPAN...NEVER BEEN USED IN AUSTRALIA!!! EXCELLENT CONDITION!

TEIN CONTROL MASTER TYPE FLEX + EDFC TO SUIT R32 GT-R OR GTS4

These electric damper adjustable coilovers allows you to control your ride while driving (: Rare and hard to get, only available on special order worth over $4000 from a local wholeseller!!!!

Details:

16 level damper adjustment

full length and height adjustment

height and spring preload adjustment

pillow ball upper mounts

++++++++++++++++++++++++++

EDFC in cabin controller (allows you to control front and rear damper settings simultaneously from the drivers seat)

4 EDFC Coilover motors + wiring included

$2500 PRICE DROP $2000 firm everything above included!!

R33

- S2 Boot with spoiler and factory Nissan lip which goes underneath the spoiler $50

- R33 Custom made speaker pods in primer ready to paint $30

- R33 Gearbox to Block Brackets $30

Contact me on my mob anytime...0417 378 515

All inspection welcomed!

Edited by Lil Miss 32

Hi All,

Up for sale is a set of white face dials for a C34 Stagea. Purchased for my series 1 installed and as i have a chrome gauge surround the chrome and white dials was a bit to much.

stagea.jpg

Sell on ebay for $77 posted.

Will sell to SAU member for $40 posted :-)

up for sale i have a complete rb20det silvertop minus loom, ecu and gearbox but all other parts are there.

the engine had 130xxxkms and was running in great condition when it was removed from our r32 to upgrade it to an rb25.

only used top quality fluids and was regularly serviced approx every 5000kms.

only asking for $500.

for more info call ph:0424687371

Response 7" Double Din DVD player.

RRP $599 at Jaycar city store, asking $380. Enquire via PM.

Comes with Manual, remote, harness & mounting hardware.

Autobarn sell a Nissan to ISO wiring harness that will fit this headunit, that means plug & play, no wire-cutting/soldering for people who don't like to mess with that stuff.

Selling: was an impulse buy now I'm bored of it, want to go back to a single-din SQ deck.

2-DIN 7" motorised widescreen with touch panel controls 

CD/DVD/SD card slot behind the panel 

Rear USB cable (have this routed to my ashtray for easy access)

Bluetooth handsfree calling and A2DP (works with my iPhone fine)

DVD/VCD/CD/MP3/WMA/JPEG/DIVX playback 

DVD/R/DVD/RW/CDR/RW

ESP and antishock mechanism 

4 channels x 20W RMS power output 

PLL tuner with 18FM/12AM presets 

3x 6v Pre-outs (front/rear/sub)

2x Rear AV inputs (can use one of these for AUX in from a portable mp3 player/phone etc.)

1x Video Out

Remote control 

Can take clearer pics on request once I get home...

post-63773-1274661398_thumb.jpg post-63773-1274661422_thumb.jpg

FS

I have a black Greddy Full Auto Turbo Timer for sale. Barely used and in great condition. These retail for roughly $130 brand new so i am after $80-$100. Also open to offers. No pics as of yet as the timer is still back at the workshop. It was installed and removed by a professional.

PMing me is the best way to go.

Hey guys up for sale is my old Kenwood mp3, CD player with front Aux input and 1 RCA preout with Sub level control with ID3 Tag. model number is KDC-mp243

I payed 125 for it last year i have upgraded recently and just wanna get rid of it, ill take $100 ONO.

Text me on 0421675373 if your interested. Need it gone Pronto

Cheers Ben

hey all,

i have a set of TE37 in white with volk stickers.

sizes: 18x8.5 +30ish and 18x9.5 +30ish

tyres are 235/40/18 all round..

rears are 95%

fronts are 80%

they are very good condition except 1 wheel has VERY light rash..

sit perfect on a r32 gtst. they dont rub anywhere on the front and car is quite low..

rears dont rub but i do have rolled guards..

$2200 FIRM..

or trade for 18x9.5+20 xt7

cheers

DSC00616.jpg

n523485035_1592807_3342513.jpg

up for sale i have a complete rb20det silvertop minus loom, ecu and gearbox but all other parts are there.

the engine had 130xxxkms and was running in great condition when it was removed from our r32 to upgrade it to an rb25.

only used top quality fluids and was regularly serviced approx every 5000kms.

only asking for $500.

for more info call ph:0424687371

words cannot describe how pissed off i am right now.

Ok guys, got this stuff for sale on the r31 forums, but i thought id throw it up on here to see if i get any interest.

Moving house this week so really wanna clear the shed to save lugging it elsewhere so open to reasonable offers.

Set of 4x 16x7 polished mesh wheels with centre caps. Multi 4 and 5 stud x 114.3

$400

ems_meshies.jpg

4x Impul Silhouette wheels. Quite rare and cool looking. 16x7 +30 and 16x8 +36 multi 4/5 stud x 114.3

Clears all 4 pot brakes (Gtr, R32, R33, S14 etc.)

$400 - Example pic (not my actual set, but the same)

AUT_0422.jpg

R32 Series 2 Dash cluster+ Brand New R32 speedo cable

Excellent condition low km's (85578kms) series 2 (grey dials) dash, Red LED's

+brand new Genuine Nissan speedo cable (very commonly break/fault in r32s)

$200 ono (may seperate if i have a buyer for both)

Genuine Hr31 Passage weathershields. awesome nick. Look like the ones on this car:

Rare as hen''s teeth, will fit aus r31s

$150

5714.jpg

Hr31 floating hubs. Perfect for brake upgrades on aus 31s.

$70

Pair of 40mm bolt on spacers. 4x114.3 stud pattern.

$70

4 stud slip on spacers. 2x pairs (1x pair 8mm, 1x pair 3mm)

$10 each pair

Brand new 2 1/4" Exhaust Y peice + stainless 2" piping. was going to use for straight pipes.

$50

Pair of rear r31 monroe Gt gas shocks with king spring lows. excellent condition.

$50

R200 Longnose Hr31 diff, welded centre, 3:4 auto ratio, comes with half shafts (1 is snapped)

$250

Genuine Hr31 passage red shagpile floor mats front and rear. Good condition. (super rare)

$70

FET turbo timer with HR31 wiring harness.

$40

Ring or sms me on 0431 320 803

please try not to pm, as i am not on these forums much anymore.

Cheers, Reece

as title says, polished D1rs in bawler off sets 18x10 all round +22 perfect on 33

Fronts have advan or kuhmo semis and rear bridgestons reo4's or sumfin

rims are immaculate xcept for light scratch on 1 that cant see.

They are polished not they ugly black ones

Lookin for $1800

Adelaide South.

Pm me

130520103229.jpg

130520103233.jpg

130520103228.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The other problem was one of those "oh shit we are going to die moments". Basically the high spec Q50s have a full electric steering rack, and the povo ones had a regular hydraulic rack with an electric pump.  So couple of laps into session 5 as I came into turn 2 (big run off now, happily), the dash turned into a christmas tree and the steering became super heavy and I went well off. I assumed it was a tyre failure so limped to the pits, but everything was OK. But....the master warning light was still on so I checked the DTCs and saw – C13E6 “Heat Protection”. Yes, that bloody steering rack computer sitting where the oil cooler should be has its own sensors and error logic, and decided I was using the steering wheel too much. I really appreciated the helpful information in the manual (my bold) POSSIBLE CAUSE • Continuing the overloading steering (Sports driving in the circuit etc,) “DATA MONITOR” >> “C/M TEMPERATURE”. The rise of steering force motor internal temperature caused the protection function to operate. This is not a system malfunction. INSPECTION END So, basically the electric motor in the steering rack got to 150c, and it decided to shut down without warning for my safety. Didn't feel safe. Short term I'll see if I can duct some air to that motor (the engine bay is sealed pretty tight). Long term, depending on how often this happens, I'll look into swapping the povo spec electric/hydraulic rack in. While the rack should be fine the power supply to the pump will be a pain and might be best to deal with it when I add a PDM.
    • And finally, 2 problems I really need to sort.  Firstly as Matt said the auto trans is not happy as it gets hot - I couldn't log the temps but the gauge showed 90o. On the first day I took it out back in Feb, because the coolant was getting hot I never got to any auto trans issues; but on this day by late session 3 and then really clearly in 4 and 5 as it got hotter it just would not shift up. You can hear the issue really clearly at 12:55 and 16:20 on the vid. So the good news is, literally this week Ecutek finally released tuning for the jatco 7 speed. I'll have a chat to Racebox and see what they can do electrically to keep it cooler and to get the gears, if anything. That will likely take some R&D and can only really happen on track as it never gets even warm with road use. I've also picked up some eye wateringly expensive Redline D6 ATF to try, it had the highest viscosity I could find at 100o so we will see if that helps (just waiting for some oil pan gaskets so I can change it properly). If neither of those work I need to remove the coolant/trans interwarmer and the radiator cooler and go to an external cooler....somewhere.....(goodbye washer reservoir?), and if that fails give up on this mad idea and wait for Nissan to release the manual 400R
    • So, what else.... Power. I don't know what it is making because I haven't done a post tune dyno run yet; I will when I get a chance. It was 240rwkw dead stock. Conclusion from the day....it does not need a single kw more until I sort some other stuff. It comes on so hard that I could hear the twin N1 turbos on the R32 crying, and I just can't use what it has around a tight track with the current setup. Brakes. They are perfect. Hit them hard all day and they never felt like having an issue; you can see in the video we were making ground on much lighter cars on better tyres under brakes. They are standard (red sport) calipers, standard size discs in DBA5000 2 piece, Winmax pads and Motul RBF600 fluid, all from Matty at Racebrakes Sydney. Keeping in mind the car is more powerful than my R32 and weighs 1780, he clearly knows his shit. Suspension. This is one of the first areas I need to change. It has electronically controlled dampers from factory, but everything is just way too soft for track work even on the hardest setting (it is nice when hustling on country roads though). In particular it rolls into oversteer mid corner and pitches too much under hard braking so it becomes unstable eg in the turn 1 kink I need to brake early, turn through the kink then brake again so I don't pirouette like an AE86. I need to get some decent shocks with matched springs and sway bars ASAP, even if it is just a v1 setup until I work out a proper race/rally setup later. Tyres. I am running Yoko A052 in 235/45/18 all round, because that was what I could get in approximately the right height on wheels I had in the shed (Rays/Nismo 18x8 off the old Leaf actually!). As track tyres they are pretty poor; I note GTSBoy recently posted a porker comparo video including them where they were about the same as AD09.....that is nothing like a top line track tyre. I'll start getting that sorted but realistically I should get proper sized wheels first (likely 9.5 +38 front and 11 +55 at the rear, so a custom order, and I can't rotate them like the R32), then work out what the best tyre option is. BTW on that, Targa Tas had gone to road tyres instead of semi slicks now so that is a whole other world of choices to sort. Diff. This is the other thing that urgently needs to be addressed. It left massive 1s out of the fish hook all day, even when I was trying not too (you can also hear it reving on the video, and see the RPM rising too fast compared to speed in the data). It has an open diff that Infiniti optimistically called a B-LSD for "Brake Limited Slip Diff". It does good straight line standing start 11s but it is woeful on the track. Nismo seem to make a 2 way for it.
    • Also, I logged some data from the ECU for each session (mostly oil pressures and various temps, but also speed, revs etc, can't believe I forgot accelerator position). The Ecutek data loads nicely to datazap, I got good data from sessions 2, 3 and 4: https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-2?log=0&data=7 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-3?log=0&data=6 https://datazap.me/u/duncanhandleyhgeconsultingcomau/250813-wakefield-session-4?log=0&data=6 Each session is cut into 3 files but loaded together, you can change between them in the top left. As the test sessions are mostly about the car, not me, I basically start by checking the oil pressure (good, or at least consistent all day). These have an electrically controlled oil pump which targets 25psi(!) at low load and 50 at high. I'm running a much thicker oil than recommended by nissan (they said 0w20, I'm running 10w40) so its a little higher. The main thing is that it doesn't drop too far, eg in the long left hand fish hook, or under brakes so I know I'm not getting oil surge. Good start. Then Oil and Coolant temp, plus intercooler and intake temps, like this: Keeping in mind ambient was about 5o at session 2, I'd say the oil temp is good. The coolant temp as OK but a big worry for hot days (it was getting to 110 back in Feb when it was 35o) so I need to keep addressing that. The water to air intercooler is working totally backwards where we get 5o air in the intake, squish/warm it in the turbos (unknown temp) then run it through the intercoolers which are say 65o max in this case, then the result is 20o air into the engine......the day was too atypical to draw a conclusion on that I think, in the united states of freedom they do a lot of upsizing the intercooler and heat exchanger cores to get those temps down but they were OK this time. The other interesting (but not concerning) part for me was the turbo speed vs boost graph: I circled an example from the main straight. With the tune boost peaks at around 18psi but it deliberately drops to about 14psi at redline because the turbos are tiny - they choke at high revs and just create more heat than power if you run them hard all the way. But you can also see the turbo speed at the same time; it raises from about 180,000rpm to 210,000rpm which the boost falls....imagine the turbine speed if they held 18psi to redline. The wastegates are electrically controlled so there is a heap of logic about boost target, actual boost, delta etc etc but it all seems to work well
    • hahah when youtube subscribers are faster than my updates here. Yes some vid from the day is up, here:  Note that as with all track day videos it is boring watching after the bloopers at the start.  The off was a genuine surprise to me, I've literally done a thousand laps around the place and I've never had instability there; basically it rolled into oversteer, slipped, gripped and spat me out. On the way off I mowed down one of the instructor's cones and it sat there all day looking at me with accusing cone eyes as I drove past. 1:13:20 was my fastest lap, and it was in the second session, 3rd lap.  It (or me!) got slower throughout the day as it got hotter.      
×
×
  • Create New...