Jump to content
SAU Community

Recommended Posts

Hi, some bits and pieces to get rid of;

  • Brand new, still in sealed packet one set of "LED Technologies" Stop/Tail/Indicator/Reflector lights, retail for $80 - Asking $70 bucks ono
  • As new electric winch, it has only been function tested to see if it works, never pulled a car/boat etc, comes with everything in the pic(Winch, 5m power cable, 2.9m remote switch lead, manual crank handle, and removable mounting bracket) plus instruction manual. this is rated at the following, rolling weight = Max 4310KG, Marine = Max 3850KG, and dead-weight pulling = 1360KG. For use on Boat and car trailers, Retail at Repco is over $200 - Asking $160 bucks ono
  • Chest webbing, only used in the field a couple for weekends, could do with a little touch up stitching, otherwise it tip top condish, not faded/all velcro works etc, fits medium to beer gut size dude, cant remember what i paid for it but asking $120 bucks ono
  • 38mm Tial copy external wastegate, used, comes as pictured, no gaskets/flanges - $50 bucks ono
  • an open R200 diff with a rear hat to suit s13, six bolt, 4.37 ratio - $120 bucks ono, i need a 5 bolt/s13 rear hat diff, let me know if you have one to swap, maybe you need to get off defect? Cash adjustment negotiable of cours an open R200 diff with a rear hat to suit s13, six bolt, 4.37 ratio - $120 bucks ono, i need a 5 bolt/s13 rear hat diff, let me know if you have one to swap, maybe you need to get off defect? Cash adjustment negotiable of course

Please contact me by phone, i'm not on SAU often so wont get PMs.

Cheers.

Ben, 0401 337 481

post-74376-0-88170700-1303049542_thumb.jpg

post-74376-0-04797900-1303049559_thumb.jpg

post-74376-0-08150000-1303049580_thumb.jpg

post-74376-0-77860000-1303049589_thumb.jpg

post-74376-0-78307000-1303049609_thumb.jpg

Few RB25 parts left over from a recent engine swap, they're all from a S2 engine unless otherwise stated.

CAS - $50

new headgasket $80

clutch fan $40

new exhaust manifold to head gasket $40

injectors and rail $80

s1 ecu $50

injector loom $40

throttle body with tps $40

r32(?) radiator $40

25det block (water/oil/sensors still attached) - 2 pistons damaged $250

Adjustable FPR $60 (I was told it was a nismo item but there is no brand/model/serial as far as i can see to identify)

PM enquiries.

Few RB25 parts left over from a recent engine swap, they're all from a S2 engine unless otherwise stated.

CAS - $50

new headgasket $80

clutch fan $40

new exhaust manifold to head gasket $40

injectors and rail $80

s1 ecu $50

injector loom $40

throttle body with tps $40

r32(?) radiator $40

25det block (water/oil/sensors still attached) - 2 pistons damaged $250

Adjustable FPR $60 (I was told it was a nismo item but there is no brand/model/serial as far as i can see to identify)

PM enquiries.

keen on the radiator but need to know if its r32 or not. does it have a fan shroud? measure the height for me if you can mate

Standard R33 Diff $150 (Stock LSD)

Standard R32 4.3 ABS Diff $150 (Stock LSD)

R33 Front S1 Red Bumper $50

235/45/17 Neuton tyres 95% left, still has the little knobbly bits. $200 for the pair

R33 Front crossmember $30

R33 Steering rack $30

R33 Power steering pump, non hicas $30

R33 Power steering reservoir $30

R33 Doors, have both drivers and passengers, $50 each

R34 Drivers door with pin dent, $50

S13/180 Fuel tank + cradle + aftermarket fuel pump $50

PM if you want anything, Cheers.

Few things for sale,

ISC R32 rear camber arms (I think they're for ceffy's also) - Brand new, bought to put on street car but then decided to sell the car and never ended up putting them on. $150

R32 drivers side Airvent. - Cut inner fins to fit gauge inside and allow the ability to move it around and point exactly to drivers view. $15

RB20 Clutch, unknown brand. - I bought a new 32 for track only, never drove it and bought a new clutch for it. Assumed it was gonna b standard. $100

Also, Greddy full auto turbo timer (like new, in black). (with handbrake sensor and speed sensor as security). plus wiring harness for R32. $40

Razo turbo timer, $10

Please sms or call 0433 975 575 coz I dont go on SAU as often now.

post-47300-0-66095900-1303129806_thumb.jpg

post-47300-0-16498800-1303129923_thumb.jpg

post-47300-0-61353300-1303130070_thumb.jpg

post-47300-0-76583800-1303130085_thumb.jpg

moving house in the next 2 months so cleaning up all my stuff i have lying around from wrecking cars over the years

if there is something you need that's not listed pm me i might have it (NO INTERIOR PARTS)

r34 boot lid with gtt wing $180

r34 2dr tail lights $100

r34 clutch fan $50

r34 neo cover $30

r34 stock intercooler core $70

r34 alternator $50

r34 air con compressor $50

r34 cross over pipe with b.o.v $50

r34 rear bar (no reverse lights) $80

r34 front guards in primer $130 each

r34 manual dash cluster $100

r34 2dr passenger door $150

r34 2dr drivers door $150

r34 gtt bonnet $200

r34 rear quarter panels $100 pair

r33 s1 type m front bar $100

r33 s1 front reo $50

r33 s2 boot lid with wing $60

r33 clutch fan $50

r33 side mount core $30

r33 alternator $50

r33 turbo elbow $30

r33 nismo clear side indicators $30

located in western suburbs s.a pm or text only 0415 23 23 97

have had my car up for sale for a while now. Somebody make me a decent offer and i'll consider it.

Link is in my sig.

just installed Tein MonoFlex's

3 months rego

118,000kms on car

90,000kms on engine

runs like a dream

new front tyres on order

Gizzmo Dual Stage Shift Light - $130 $100

post-3189-0-16674200-1302337958_thumb.jpg

R32GTR Rear Brakes $250 $200 - Brake ducts / genuine nissan rotors / Endless Pads / braided lines / rebuilt calipers excellent condition

RB26 ACL Head Gasket - used but good condition and REUSABLE. $100 $80

post-3189-0-99625000-1302338371_thumb.jpg

SARD 700cc Injectors (RB26) $550

Price drop

Edited by Blue32

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...