Jump to content
SAU Community

Recommended Posts

I have two nismo engine mounts for sale - model 11220-RS540. They have stickers on them incorrectly marking for an R34, but as per the nismo model number they're the front left engine mount on a Nissan 180SX PS13, RPS13, S14, S15.

As per the marketing blurb from nismo:

Nismo mounts are 30-40% stiffer which makes motor shake less at idle and the Nismo transmission mount provides precise shifting at high rpm from reduced motor/transmission movement.

Obviously if you're wanting to upgrade, you'll probably want the front right & transmission mount as well - which I do not have - but they're easy enough to source online.

They're brand new in the box - never used. Looking for $100 each.

mounts-small.jpg

Daily Driver

1990 AE92 Toyota Corolla

4A-F Engine,1.6L Four-Cylinder, Carburettor fed.

5 Speed Manual

Factory "Grey" Colour

Standard "steelies"

Body panels are relatively in good nick. Paint has seen better days - mainly faded on the roof, one of the front guards, and the hatch.

Drives well - I have owned it for 2.5 years and had no problems with it whatsoever. Just kept it topped up with oil and water and hasn't missed a beat. Only noticable issue was the battery light would flicker on from time to time - I check the charge voltage and the alternator - these tested fine.

This car is the perfect cheap runabout for someone with a play car that needs a car just to get to and from work. I usually get around 7-8L/100km economy which is pretty good considering its run off a carby.

I believe the rego is still valid until October but will have to check.

I am getting rid of it because I have a new daily (2003 VY SV8) which I got at a price I couldn't refuse.

Looking for $1000 ONO.

Can get photos for you if needed.

Contact me via PM or send me a text on 0401 THREE ONE SEVEN ZERO ZERO NINE.

Cheers,

David

Edited by R32Abuser

up for sale is my 95 R33 GTST

ive owned the car since 07 and bought it in darwin already painted purlpe.

reason for selling is i now have 3 cars and i dont drive it anymore

the mods on the car:

front strut brace

full bomex bodykit

Viper alarm system

dash surround is painted the same colour as the outside

adjustable camber kit

3"cat back exhaust

splitfire coil packs

front mount intercooler

hicas lock bar

exeedy 6 puk button clutch

legal lowered springs

A pillar twin guage cluster with autometer boost and A/F ratio guages

Greddy turbo timer

Exhaust silencer

sard fuel pressure reg

z32 Air flow meter

apexi pod filter

apexi power FC boost controller - not connected

has 3 months rego

has new tyres all round

timing belt and major service done at 110xxx

the seats have no tears or rips

the bad points:

the front bar needs some work

the roof at the back has a small dent

the front left guard needs mending

if you have any questions, feel free to ask.

$9,000 ONO - make an offer

PM me for pictures as I don't know how to upload them

-Z32 removed

price dropped as synchro is letting go in 4th

$7000

Still for sale, reduced to $8,500! Sad to see it go but I'm looking to buy a house and need the cash.

Mint condition modified Skyline.

All modifications less than 10,000kms old

GCG high flow turbo

Apexi Power FC with hand controller

Blitz stealth front mount intercooler

Dual stage electronic boost controller with gauge

Full 3 inch exhaust with high flow cat

Nismo 555cc injectors

DBA slotted rotors and QFM pads

BC Racing fully adjustable coilovers

Camber and Caster Adjustable poly bushes in the front end

Dual port BOV

Excedy HDCB Clutch

Walbro Highflow Fuel Pump

Always regularly serviced with the highest quality oils, never been tracked. Probably many other mods I have forgot. Has been tuned at boostworks and is currently making 245rwkws. With a more free flowing exhaust system the current set up is good for a 20 odd extra kws according to the tuner, however the neighbours will rather the current system. Reason for selling, we now have 3 cars and just bought a 4x4 unfortunately I don’t get to dive this as much as I would like. Please give me a call to arrange a time to view on 0400297840.

IMG_1710.jpg

IMG_1703.jpg

IMG_1701.jpg

Ssr fellinis 19x9+14 & 19x8.5+20 nice deep dish rare rims , I love these rims but selling due to going narrower rear sub frame so I can squeeze biggier rims under, just an EOI ATM very small amount of rash on one rim see pic $1500ono no tyres

post-76904-0-75792700-1377741627_thumb.jpg

post-76904-0-79993000-1377741689_thumb.jpg

stagea

firm price, 8k. engine alone is worth that, easy.

AS-IS; havent a cent to my name so I cant do anything with it :(

http://www.skylinesaustralia.com/forums/topic/380883-sa-1997-nissan-stagea-rs4/

BA Falcon XR6T

Narooma Blue

BTR 4sp Auto

2 owners (1 Previous)

93,000ks

-Full service history

-Factory Leather

-Factory Premium Sound

-Factory Sat Nav

-Upgrade speakers, (f)Pioneer TS-A1702C components ®JL Audio C2 570X


-External transmission cooler (bypass radiator)

-Transmission service / new fliuid

-Replaced diff oil & brake fluid

-New spark plugs

-Cleaned throttle body / boost control solenoid

-Aftermarket FMIC

-New whiteline sway bar D bushes

-SS Wide Mouth Induction Kit

-Heinrich Tune - excellent mid range performance.

-Slotted front rotors and Remsa high performance pads

-Pedders sports ryder rear springs (to remove factory rake)

-18% window Tint (Dec 2012)

-BBS LM Replica Wheels, (f) 19x8.5 (245/35) & ® 19x9.5 (275/30) ~6,000kms old

-Full Stage 2 detail and Opticoat Paint Protection applied July 2013 By Elite Finish


Simply, fuel bill can no longer be supported on single income (wife now home with kids)

Not in a rush to sell so not accepting stupid offers.

$13,900


$T2eC16F,!)MFIbp1qkGnBSI9g6WM7w~~48_20.J


$(KGrHqV,!lMFIOOF548PBSI9g+GqWg~~48_20.J

Ssr fellinis 19x9+14 & 19x8.5+20 nice deep dish rare rims , I love these rims but selling due to going narrower rear sub frame so I can squeeze biggier rims under, just an EOI ATM very small amount of rash on one rim see pic $1500ono no tyres

R32 gtr standard turbos $200

R32 gtr standard dump pipes $40

R32 gtr standard intercooler pipes (missing one joining twin turbo pipe) $40

R32 gtr AC condenser and fan $40

R32 gtr AC compresser and lines $60

R32 gtr under bonnet carpet $20

R32 gtr n1 front bumper vent 1 side $20

R32 gtr front bumper intercooler mesh $50

R32 audio and gear stick surround in wrinkle finish, cigarette lighter has been cut out $40

Blitz ss blow off valves suit rb26 $200

Also have standard 180sx rear lights plus centre garnish $50

Aftermarket 180sx side skirts $100

Black Hks ssqv blow off valve $40

S13 Silvia passenger head light $40

For pictures send me a text 0430961312

Feel free to make offers and will swap for r32 gtr parts. Need everything gone!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
    • Nah, that is hella wrong. If I do a simple linear between 150°C (0.407v) and 50°C (2.98v) I get the formula Temperature = -38.8651*voltage + 165.8181 It is perfectly correct at 50 and 150, but it is as much as 20° out in the region of 110°C, because the actual data is significantly non-linear there. It is no more than 4° out down at the lowest temperatures, but is is seriously shit almost everywhere. I cannot believe that the instruction is to do a 2 point linear fit. I would say the method I used previously would have to be better.
×
×
  • Create New...