Jump to content
SAU Community

Recommended Posts

HI ALL,,,

I have a r33 with RB25, Power Fc with hand controller,

Up untill yesterdy all was fine, not had a prob before with it.. water temp would sit 78 - 80 once fully warned up after (about 5 minutes) and might creep up to 83 after few hours driving,Fine right? been like that for years

Right,

My cars been sitting in the pannelbeaters the last couple months, (front bumper damage and minor side pannel damage) the radiator didnt get touched atall in accident baring in mind, but they had to remove the rad to do work, when i went to the place yesterday car was running, they said it had been running a couple of minutes and i looked at Fc hand controller and Water said 60.... i then revesed straight out of the unit (20ft) got outta car. talked for honestly no more than two minutes, Got back in car and hand controller was reading 114c!! pannelbeater says nah that cant be right because the stock temp gauge is only reading just above halfway mark?

Please all! Am gratefull of all advice!!

CHEERS AGAIN

Link to comment
https://www.sau.com.au/forums/topic/355488-r33-gtst-extrem-over-heating/
Share on other sites

Let it cool Nd check the coolant level. If its ok leave the cap off open the air bleeder screw on the inlet manifold till coolant comes out then refit the bleeder screw and start the car, let it idle till it warms up with cap off and heater on.

This should remove any air that is still trapped in the cooling system.

If it still overheats get a new thermostat

pannelbeater says nah that cant be right because the stock temp gauge is only reading just above halfway mark?

in my experience, the stock temp gauge reaches half-way around 60-65C and will stay there till around 110C before rising - so it could be easily right.

+1 on bleeding the coolant system too.

You may have air in the sysyem, When the car is cool remove the radiator cap and start the car, let the car idle for a while(might take 5-10 minites), giving it a few revs here and there, watch your temp gauge, and add coolant as needed, also ensure you have some coolant in the overflow for when the car cools down so it doesnt suck air back in.

Might fix it.

Mark

in my experience, the stock temp gauge reaches half-way around 60-65C and will stay there till around 110C before rising - so it could be easily right.

+1

Basically from my experience the stock temperature gauge should always be reading just under 1/2 way for a normal operating engine at normal temperature.

If it gets to 1/2 mark then thats enough to throw a caution, anything over 1/2 means there are potential over heating issues with the engine.

I had my gauge read just over 1/2 way & when I pulled over the coolant was boiling in the reserver tank, even though according to the stock gauge it's no where near the H mark, had it checked & it turned out to be a worn Rad cap & thermostat.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...