Jump to content
SAU Community

Recommended Posts

I recently bought an RB25 to put into my R32. I was pulling it down last night to have a look at the condition and give it some new gaskets and timining belt etc. When i pulled the harmonic balancer off i noticed that one side of the keyway seems to have been flogged out. (see pic!)

What's the easiest way out from here? Is it repairable? If so is it safe/reliable to do so? Or am i better off tracking down a good condition crank and just replacing it?

Thanks guys!

post-20417-0-37431700-1299727941_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/
Share on other sites

spewin, one of my trucks just spat the crank pulley and the key way isnt quite that bad, hopefully i can fix it without a new crank or the truck is going in the bin...

Large bin or small truck?

So it's not really viable to fix this? Inconvenient!

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5707794
Share on other sites

it can be fixed. the keyway just locates the balancer. it doesn't actually turn it, that's done with the force of the bolt holding it on (just like wheel studs don't turn your wheels the hub face does).

they get damaged when balencers come loose, without the bolt then the key is turning the damper and it just gets bashed to bits.

not many people are willing to repair them but herman at envy imports in sydney can do them. i've seen him do a few and all the one I know of are still living a happy life. talk to him about cost for repair and then figure out if it's worth doing vs a new crank.

Jez: he could probably fix your truck one too.

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5707800
Share on other sites

Fitting a new key with epoxy or metal magic to take up the flogged out space, plus a new balancer, will work. For how long I cannot say, but I repaired a ca18det in the same way and it has since done 5000km at 180rwkw without a problem.

Still, not ideal, but since the filler material has no where to go and as long as the bolt is tightened properly it works.

On a ca20 junker I replaced balancer and key and epoxied, that's since done about 10000km and been apart twice for headgaskets haha

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5708125
Share on other sites

Ok maybe I should re-clarify - yes you can fix it, there are many ways to fix it. There are no ways to fix it properly. If you rev it too high the balancer will come loose again due to the harmonic vibrations and microscopic movements and twisting of the crank. Heat will also play a part in it's demise.

Fix it, but know the risks if you do

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5708187
Share on other sites

I understand where you're coming from. Since the car is still running fine with the current engine and i have the time up my sleeve, i'm leaning towards tracking down a crank in good condition. I do intend on leaning on this motor a bit so i'd like to do it right first time around.

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5708262
Share on other sites

This is really common on RB30's, I've had 2 cranks with slogged out keyways. I just sand/gently file any ridge/warping then use some locktite liquid metal (it actual says for keyway repair on the tube) stick the keyway in and let it set, slip on the balancer and torque the bolt to a tasty 500nm :P (aka as hard as you can). $12 fixed.

Did this on my RB30DE which revs fast and high frequently (hi comp, cammed, short geared, lightened and balanced) and it has never had a problem.

Edited by SKiT_R31
Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5708964
Share on other sites

I recently had one repaired by a company called industrial hardchroming in Sydney, They weld it, then chrome it and grind, recut the keyway, only cost about $200

yep, same basic way as herman repairs his (he does have another little trick too). most will also need a new balancer as mentioned above as if they have come loose they tend to wear. the main thing is getting the crank snout repaired properly so the new balancer is a good fit. then with new keyway, new balancer bolt, new washer and new backing plate it should all go together nicely and live just like a bought one. :)

herman is at http://www.envyimports.com.au/contact_us.html

02 9907 4144

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5709181
Share on other sites

I'm with skit r31. It's a key way to locate the balancer, nothing else, and the damage isn't that bad, one side is still perfect so you can still line it all up right. If the slot in the balancer is flogged out then replace it.

If the crank was already out then yeah, $200 cheap fix.

But it's not; As soon as you pull that engine apart you may as well have thrown it in the bin and bought another 3 s/h short engines as you won't get change from 2.5k to have someone that knows what they are doing put the whole thing back together properly. Not some monkey that passes them self off as an engine builder.

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5709340
Share on other sites

To check I understand what's been said above and the bits i know - is this a good summary?

- the keyway is only use to locate the balancer during installation, and does nothing once the bolt is installed

- the only reason the balancer needs to be located is so the timing marks are in the correct location (ie it's not counterweighted or ??)

- so the only effect of a worn keyway is that the timing marks will be a little off

But if i understand Elite, he's saying the balancer will come loose again if the keyway is stuffed and the motor is revved high.

Que?

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5709593
Share on other sites

yeah mate that's pretty much it.

I think ERD's problem with it is this. usually when balancers come loose and damage the keyway sometimes they damage the rest of the crank snout too and the balancer. in those cases just repairing the keyway wont help with the balancer fitting properly on the snout. fixing the whole surface properly and replacing the balancer is the way to go.

as far as the balancers being weight indexed to a certain spot I'm not sure, but I think they are not. each component from the factory is balanced separately. they are not actually a balancer anyway, they are a harmonic dampener and crank pulley. there is a slight difference between the two.

still I have no problem using a repaired crank as long as it's repaired properly and the balancer and bolt etc is replaced.

would I used a repaired crank as the basis for a mega $$ engine? probably not. but I had no problem revving my old one to 8,300rpm after it was repaired.

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5709730
Share on other sites

That's pretty much it BB. The fact the keyway was damaged means the balancer had been moving around. This will either micro weld the crank to the inside of the balancer or it will machine down the snout of the crank. This means any new balancer that goes on or the old one, will not have enough or any interference against the crank snout. The amount of movement there when you are revving past 7k would scare you. The purpose of the balancer/dampener is to remove harmonic vibrations from the crankshaft. If it is able to move due to the bearing retainer or loctite material not being able to sustain high bonding strength for more than a short time, it will surely come loose again or destroy the oil pump.

I know people who have welded balancers on to cranks and not had problems. I know people who have repaired keyways and not had problems, I also see the ones that were apparently repaired correcty and have come unstuck. If it were my car and I had to choose, I'd choose to replace it.

If the repair is done by welding the snout of the crank, you also risk the end of the crank snapping off. I know people had done this without any problems but once again, I have seen the other side of the coin too. Why risk it. Cranks are not expensive and fairly easy to come by

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5709816
Share on other sites

That's pretty much it BB. The fact the keyway was damaged means the balancer had been moving around. This will either micro weld the crank to the inside of the balancer or it will machine down the snout of the crank.

Ok so the OP needs to check the dimensions (snout OD, balancer ID, roundness) with a micrometer. If the snout OD is within spec then its reasonable to repair the keyway, if not, new crank. If the balancer ID is out of spec then just get a new balancer.

If the gap is a little bit more than spec, would it be possible to dodgy up some of the clearance with a locktite product?

Also, I'm guessing the crank should be annealed after welding (assuming its safe to do so) to really do the job correctly.

Link to comment
https://www.sau.com.au/forums/topic/356805-crank-damage/#findComment-5710490
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Haggerty this is your red flag. In MAP based ECU's the Manifold pressure X RPM calculation is how the engine knows it is actually...running/going through ANY load. You are confusing the term 'base map' with your base VE/Fuel table. When most people say 'base map' they mean the stock entire tune shipped with the ECU, hopefully aimed at a specific car/setup to use as a base for beginning to tune your specific car. Haltech has a lot of documentation (or at least they used to, I expect it to be better now). Read it voraciously.
    • I saw you mention this earlier and it raised a red flag, but I couldn't believe it was real. Yes, the vacuum signal should vary. It is the one and only load signal from the engine to the ECU, and it MUST vary. It is either not connected or is badly f**ked up in some way.
    • @Haggerty you still haven't answered my question.  Many things you are saying do not make sense for someone who can tune, yet I would not expect someone who cannot tune to be playing with the things in the ECU that you are.  This process would be a lot quicker to figure out if we can remove user error from the equation. 
    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
×
×
  • Create New...