Jump to content
SAU Community

high 13s???

drewecrome

By drewecrome,
in Western Australia

 Share

Recommended Posts

drewecrome Rising Star

drewecrome

Posted
Posted

hey all, i will be in the market for an r33 gtst skyline in june, i have budget of $19000, but want money left over for mods, im willing to spend between $17000, and $17500 for a decent car. with the left over money i want to spend it on mods that will get me into the high to medium 13 brackets, i would like any info on how thish could be achieved, with around $2000, taking into account that the car i will buy will probably have an exhaust and an air filter, any hints, or ideas? please help.

Link to comment
https://www.sau.com.au/forums/topic/35759-high-13s/
Share on other sites
caminperth Grand Master

caminperth

Posted
Posted

Lightened flywheel is one way to go - but can make the car harder to drive and hard to launch properly..

another way is a full turbo back exhaust, pod and a bit more timing.. that and perhaps a bleed valve for a bit more boost should see you with a late 13 easy....

Link to comment
https://www.sau.com.au/forums/topic/35759-high-13s/#findComment-713936
Share on other sites
Nexus_SiX Community Regular

Nexus_SiX

Posted
Posted

I bought an R33 with exhaust and pod. I have bought a power FC and boostcontroller with has got me to 13.7

This would be slighty more than 2 grand with retail prices, however the same basics would be availabe with a Air/fuel computer e.g AFC and a boostcontroller. Both could be yours for as little as $500 ( if using the 2nd hand route)

Say hello, listen to peoples various suggestions. Take what you think is best and go with it.

welcome to the community :D

Link to comment
https://www.sau.com.au/forums/topic/35759-high-13s/#findComment-713969
Share on other sites
rev210 Grand Master

rev210

Posted
Posted
Lightened flywheel is one way to go - but can make the car harder to drive and hard to launch properly..  

another way is a full turbo back exhaust, pod and a bit more timing.. that and perhaps a bleed valve for a bit more boost should see you with a late 13 easy....

The lightweight flywheel fitted to my old car did nothing to make the car harder to launch or drive. I put one in my car and there was no issues at all. I didn't think you had a lightweight flywheel in your car Cam, perhaps it has a balance issue or something.

If you want a flywheel that has been tested by a few then the ogura 4.8kg is a sure bet.

Link to comment
https://www.sau.com.au/forums/topic/35759-high-13s/#findComment-714344
Share on other sites
caminperth Grand Master

caminperth

Posted
Posted

No issues with balancing - it's a stocker.. A light flywheel by design will make the car rev harder and faster, but will also loose momentum easier than a stocker if not taken into account when launching and during normal driving..

Anyways - a high 13 should easily be within reach with some or all of the mods listed..

Link to comment
https://www.sau.com.au/forums/topic/35759-high-13s/#findComment-714424
Share on other sites
rev210 Grand Master

rev210

Posted
Posted

b005t,

the fuel ecconomy is slightly better (accelleration uses more fuel than cruising obviously). The car will slow down faster (engine braking) when the throttle is shut in gear, coasting you do with the clutch 'in' therefore no difference.

The car is easier to launch and nicer to drive , any comment's to the contrary are incorrect speculation.

I believe the lightweight flywheels are now $600 or less, a bargain!

When I get the gtr I'll be fitting one to that for sure.

Link to comment
https://www.sau.com.au/forums/topic/35759-high-13s/#findComment-718526
Share on other sites
rev210 Grand Master

rev210

Posted
Posted

yes it would have an adverse effect on an auto since the auto has no clutch and flywheel to begin with :starwars: . Bottom line ios you can't do this mod to an auto.

Auto's benifit from modifications to the stall convertor and valve body tho'. the first increases the stall rpm and torque multiplication for great launches. The second increases the speed at which the auto can be shifted and reduces the 'slip' into each gear.

Link to comment
https://www.sau.com.au/forums/topic/35759-high-13s/#findComment-718811
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...